manualshive.com logo in svg

HIAB 410K PRO, Operator'S Manual, Page: 46 / 82

Share
Download
HIAB 410K PRO Operator'S Manual Download Page 46

DANGER

Always  ensure  that  the  stabiliser  legs  and  stabiliser  extensions  are  in  working
position and securely locked.

Never operate up any stabiliser leg if you have load on the crane.

Put the extra support plates

• Put  the  extra  support  plates  under  the  stabiliser  leg

plates (if necessary).

DANGER

Do a check that the support plates do not bend or sink into the ground!

Non-tiltable stabiliser legs

1.

Make sure that the stabiliser extensions are extended.

2.

Put  the  extra  support  plate  (1)  onto  the  ground  (if
necessary).

3.

Operate  the  stabiliser  leg  downwards  until  it  is  set  to
the ground.

5.5. Operate the boom system out of transport position

WARNING

• A crane with add-on equipment can differ from the operations described in this

section.

• For this reason study the operating instructions for add-on equipment carefully.

Once the stabiliser extensions and legs are ready you can start using the crane.

1

Starting crane operation

46

HIAB 410K PRO

Summary of Contents for 410K PRO



















































































Reviews:

No comments