HHP Adaptus Image Kiosk TT8870 Programming Manual Download Page 134

Page: 134 / 149

10 - 2

Image Kiosk™ TT8870 Programming Guide

Technical Assistance

If you need assistance installing or troubleshooting your scanner, please call
your Distributor or the nearest HHP technical support office:

North America/Canada:

Telephone:

(315) 685-2476, Option 4 (8 a.m. to 6 p.m. EST)

or in the U.S.

(800) 782-4263

Fax number:

(315) 685-4960

E-mail:

[email protected]

Europe, Middle East, and Africa:

Telephone-
European Ofc: Int+31 (0) 40 29 01 600
U.K. Ofc:

Int+44 1925 240055

E-mail:

[email protected]

Asia:

Telephone:

Int+852-2511-3050

or 2511-3132

E-mail:

[email protected]

Latin America:

Telephone:

(239) 263-7600

E-mail:

[email protected]

*Deactivate

Activate

Summary of Contents for Adaptus Image Kiosk TT8870






















































































































































Search results

Summary of Contents for Adaptus Image Kiosk TT8870

Reviews:

Related manuals for Adaptus Image Kiosk TT8870

Brands by name

Popular brands

HHP Adaptus Image Kiosk TT8870, Programming Manual

Search results

Summary of Contents for Adaptus Image Kiosk TT8870

Reviews:

Related manuals for Adaptus Image Kiosk TT8870

Brands by name

Popular brands