manualshive.com logo in svg

HGST H4060-S, Installation Manual

Share
Download
HGST H4060-S Installation Manual Download Page 12

handling the unit. Always team lift the chassis by gripping the underside of the unit, and never try to lift
a chassis that is filled with drives.

Figure 5: Installation, Servicing, and Removal

1.4.1

Compatible Hardware Configuration

The following table(s) list the approved hardware configurations for the Ultrastar 8:

Table 7: Compatible Hardware Configuration 1

Additional Mounting
Bracket Hardware

PDU Mounting
Bracket

PDU (Vertical)

Rack

Parameter

Various

Server Technology

Server Technology

CRENLO/EMCOR

Vendor

4 x M6 x 16 Hex Cap
Screws

KIT-MBVPT-1B (one
kit per PDU)

412-0761-11_STV-4501

412-0761-20_STV-4502

AS-160099-03
(Drawing Number
EMCOR 526121 Rev
5)

Part
Number

8 x M6 Fender
Washers

412-0761-23_STV-4503

4 x M6 Hex Nut with
Nylon Lock

Varies

2

2

1

Quantity

Table 8: Compatible Hardware Configuration 2

Additoinal Mounting
Bracket Hardware

PDU Mounting
Bracket

PDU (Vertical)

Rack

Parameter

Various

Server Technology

Server Technology

AFCO/Legrand

Vendor

None

KIT-MB-40

412-0761-11_STV-4501

Options:

42RU – WEDIT605

Part
Number

412-0761-20_STV-4502

12

1

Overview

Installation Guide

1.4

Ultrastar 8 Rack Requirements

Summary of Contents for H4060-S





















































Reviews:

No comments

Brands by name

Popular brands

Load more brands