HF PackerAmp V4 Construction Manual Download Page 41 | Manualshive

Page: 41 / 76

background image

HF PACKER

AMP

V4R6

Page 41

PTT Connections FLEX 1500 and FT817

FLEX 1500 – Connect the center wire from the PTT jack to pin

pin 3 of a serial connector which corresponds to the Flex 1500
Flexwire connector on the back of the radio. This connection
allowed the Flex 1500 to key the Packer Amp. Do not connect
the ground connection as the Amp and Radio are already
referenced to the same ground. Using an additional ground
connection has been reported to cause distortion.

FT817 – Connect the center wire from the PTT jack to pin 1 of
the ACC jack on the FT817 (PTT). Do not connect the ground
as the Amp and Radio are already referenced to the same
ground. Using an additional ground connection has been
reported to cause distortion.

«
...
39
40
41
42
43
...
»

Summary of Contents for PackerAmp V4













































































Reviews:

No comments

Related manuals for PackerAmp V4

Brand: e-motion Pages: 13

Brand: NAD Pages: 2

Brand: Ramsey Electronics Pages: 20

Brand: SMSL Pages: 8

Brand: Primare Pages: 10

Brand: ESX Pages: 20

Brand: Lynx Pages: 22

AMP50 - XTR 1000

Brand: W Audio Pages: 8

Richer Bass RB1

Brand: Laney Pages: 12

Brand: Ibanez Pages: 20

ZeroUno DAC-HPA

Brand: Canever Pages: 8

Brand: icon Audio Pages: 10

Brand: Orion Pages: 21

Brand: Texas Instruments Pages: 10

Brand: JET CITY AMPLIFICATION Pages: 18

Bassman Bassman 100

Brand: Fender Pages: 16

Brand: Lab.gruppen Pages: 12

Brand: AR Pages: 80

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands