manualshive.com logo in svg

Hewlett Packard Enterprise ProLiant DL20 Gen10, Maintenance And Service Manual

Share
Download
Hewlett Packard Enterprise ProLiant DL20 Gen10 Maintenance And Service Manual Download Page 112

Intelligent Provisioning includes the following components:

• Critical boot drivers

• Active Health System (AHS)

• Erase Utility

• Deployment Settings

IMPORTANT:

• Although your server is preloaded with firmware and drivers, Hewlett Packard Enterprise recommends updating

the firmware upon initial setup. Also, downloading and updating the latest version of Intelligent Provisioning
ensures the latest supported features are available.

• For ProLiant servers, firmware is updated using the Intelligent Provisioning Firmware Update utility.

• Do not update firmware if the version you are currently running is required for compatibility.

NOTE: Intelligent Provisioning does not function within multihomed configurations. A multihomed host is one that is
connected to two or more networks or has two or more IP addresses.

Intelligent Provisioning provides installation help for the following operating systems:

• Microsoft Windows Server

• Red Hat Enterprise Linux

• SUSE Linux Enterprise Server

• VMware ESXi/vSphere Custom Image

• ClearOS

Not all versions of an OS are supported. For information about specific versions of a supported operating system, see the
OS Support Matrix on the Hewlett Packard Enterprise website (

https://www.hpe.com/info/ossupport).

HPE Insight Remote Support

Hewlett Packard Enterprise strongly recommends that you register your device for remote support to enable enhanced
delivery of your Hewlett Packard Enterprise warranty, HPE support services, or Hewlett Packard Enterprise contractual
support agreement. Insight Remote Support supplements your monitoring continuously to ensure maximum system
availability by providing intelligent event diagnosis, and automatic, secure submission of hardware event notifications to
Hewlett Packard Enterprise, which will initiate a fast and accurate resolution, based on your product’s service level.
Notifications can be sent to your authorized Hewlett Packard Enterprise Channel Partner for onsite service, if configured
and available in your country.

For more information, see Insight Remote Support and Insight Online Setup Guide for ProLiant Servers and BladeSystem
c-Class Enclosures on the 

Hewlett Packard Enterprise website. Insight Remote Support is available as part of Hewlett

Packard Enterprise Warranty, HPE support services, or Hewlett Packard Enterprise contractual support agreement.

HPE InfoSight for servers

The HPE InfoSight portal is a secure web interface hosted by HPE that allows you to monitor supported devices through a
graphical interface.

Diagnostic tools

112

Summary of Contents for ProLiant DL20 Gen10


























































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands