Hewlett Packard Enterprise OfficeConnect 1850 2XGT Installation And Getting Started Manual Download Page 38

Specifications

Switch Specifications

A-2

Environmental

Acoustics

Safety

Complies with:

EN60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 / IEC60950-1:2005; Am1:2009;

CSA22.2 No. 60950-1-07 2nd Ed.; UL60950-1 2nd Ed.

EN 60825-1:2007 / IEC 60825-1:2007 Class 1

EMC

EMC: EN 55032:2015, Class A

EN 55024:2010

EN 61000–3–2:2014

EN 61000–3–3:2013

FCC CFR 47 Part 15B:2014, Class A

Operating

Non-Operating

Temperature

0°C to 40°C (32°F to 104°F)

-40°C to 70°C (-40°F to 158°F)

Relative humidity (non-condensing)

15% to 95% at 40°C (104°F)

15% to 95% at 65°C (149°F)

Maximum altitude

3.0 km (10,000 ft) *

4.57 km (15,000 ft)

* The operating maximum altitude should not exceed that of any accessory being connected to any 1850 Switch. 

Switch

Noise Emission

1850 6XGT 2XGT/SFP+ (JL169A)

Sound Power (LwA) 4.5 Bel
Sound Pressure (LpAm) (Bystander) 37.9 dB

1850 24G 2XGT (JL170A)

Sound Power (LwA) 3.6 Bel
Sound Pressure (LpAm) (Bystander) 30.5 dB

1850 48G 4XGT (JL171A)

Sound Power (LwA) 3.4 Bel
Sound Pressure (LpAm) (Bystander) 30.5 dB

1850 24G 2XGT PoE+ (JL172A)

Sound Power (LwA) 4.4 Bel
Sound Pressure (LpAm) (Bystander) 33.6 dB

1850 48G 4XGT PoE+ (JL173A)

Sound Power (LwA) 4.0 Bel
Sound Pressure (LpAm) (Bystander) 31.1 dB

Summary of Contents for OfficeConnect 1850 2XGT

























































Reviews: