manualshive.com logo in svg

Herz pelletfire 20/20, Operating Instructions Manual, Page: 28 / 100

Share
Download
Herz pelletfire 20/20 Operating Instructions Manual Download Page 28

9 

Menu navigation and adjustment values 

 

28 

 

9.7 

Switching the boiler on and off (chimney sweeping function) 

SWITCH-ON 

SWITCH-OFF 

 

 

 

 

Navigation: 

 

Navigation: 

 

Screen: 

Screen: 

 

 

By pressing the button: 

By pressing the button: 

 

the boiler will be switched on. 

 

the boiler will be switched off. 

 

the  boiler  will  switch  off,  remains 
off  and  the  previous  page  will  be 
displayed. 

 

the  boiler  remains  on  and  the 
previous page will be displayed. 

Note: 

Note: 

The  system  can  only  be  switched  on if  there  are  no 
errors that prevent it from starting. 

The boiler will switch to the operating condition “burn 
out  phase”  (except  “cold  start”  or  “ready”).  When 
switching off during cold start, the cold start is ended 
and  then  changes  to  the  burnout  phase.  This 
prevents  impermissibly  high  amount  of  fuel  in  the 
combustion chamber. 

 

               CHIMNEY SWEEPING FUNCTION 

 

Navigation: 

 

Screen: 

 

 

If  “chimney  sweeping  function”  is 
active, the remaining time can be 
raised  in  5  minutes  steps  by 
pushing the 

-button. 

 

Raises 

the 

remaining 

time 

(chimney  sweeping  mode)  by 
5 minutes steps. 

After pressing the chimney sweeping symbol, the 
boiler can also be switched off. 

 

Summary of Contents for pelletfire 20/20





































































































Reviews:

No comments