manualshive.com logo in svg

HermanMiller Embody 100210688, Manual

Share
Download
HermanMiller Embody 100210688 Manual Download Page 17

©

2008 Herman Miller, Inc., Zeeland, Michigan  Printed in U.S.A.

™

L

, 

Z

, 

Y

, Embody, are trademarks of Herman Miller, Inc.

 

 Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make  

         changes in design and specifications at any time, without notice, and also to discontinue products.

1B4YJB REV A

PARTS INCLUDED:

TOOLS REQUIRED:

1

Seat Fabric

 

2

Bolts

3

Bolts

         

          T-30 T-40

Tension
Adjustment Rod

Remove lower spine bolts using t-40 torx 
wrench

Remove lower back bolts using t-40 torx 
wrench

       Torx bits

 Ratchet

 Torque Wrench

T-27

S-Clip (2)

Seat Slide Guide (2)

Fabric Cable (2)

Spring (2)

Lower Fabric Attach Strips (LH, RH)

Remove back tension adjustment rod by insert-
ing 1/16” allen wrench underneath rod to 
release and then pulling out.  (Chairs built prior 
to 4/3/09 can be removed by wiggling up and 
down while pulling out to disengage.)

 1/16” Allen Wrench

Embody

™

Seat Fabric Replacement

Summary of Contents for Embody 100210688

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands