HermanMiller Embody 100210688 Manual Download Page 112

Page: 112 / 128

2008 Herman Miller, Inc., Zeeland, Michigan Printed in U.S.A.

™

, Embody, are trademarks of Herman Miller, Inc.

Illustrations and specifications are based on the latest product information available at the time of publication. The right is reserved to make

changes in design and specifications at any time, without notice, and also to discontinue products.

1B7061 REV A

Embody

™

Tilt Replacement

PARTS INCLUDED:

TOOLS REQUIRED:

Tilt

Bolts

Remove back tension adjustment rod by insert-
ing 1/16” allen wrench underneath rod to
release and then pulling out. (Chairs built prior
to 4/3/09 can be removed by wiggling up and
down while pulling out to disengage.)

T-30 T-40

Tension
Adjustment Rod

Remove lower spine bolts using t-40 torx
wrench

Remove lower back bolts using t-40 torx
wrench

Torx bits

Ratchet

Torque Wrench

T-27

Needlenose Pliers

Flat Blade
Screwdrive

8mm Socket Knock-off Tool

S-Clip (2)

1/16” Allen Wrench

Tension Shaft Assembly

Summary of Contents for Embody 100210688

































































































































Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands

HermanMiller Embody 100210688, Manual

Search results

Summary of Contents for Embody 100210688

Reviews:

Brands by name

Popular brands