Henry Airtools 56 VL General Safety And Maintenance Manual Download Page 5

Page: 5 / 11

HENR

OOLS,

INC.

Ph:

(216) 291-1011 or (800) 826-5257

General Operators Instructions and Service Manual

www.HenryTools.com | Page 175

Revised 12/10/15

For additional product information visit our website.

PART NO.

DESCRIPTION

AA-560-1

CASE ASSY.(Comes with all screws)

Specify the speed

AA-650-1-AL

LEVER LIVE HANDLE ASSEMBLY

COMPLETE with screwsNON lockout

Style

AA-650-1-ALS

LOCKOUT LEVER LIVE HANDLE AS-

SEMBLY COMPLETE with screws

OVERNORS

AA-550-45

GOV.ASSY. (4500 RPM)

AA-550-60

GOV.ASSY. (6000 RPM)

AA-550-72

GOV.ASSY.(7200 RPM)

AA-550-80

GOV.ASSY. (8000 RPM)

• OTHER SPEEDS AVAILABLE

ACCESSORIES

849259

5/8-11 Sanding Pad Nut

849913

7” SANDING PAD

(MAX 8500 RPM

849914

9” SANDING PAD (MAX 6500RPM)

849269

DEPRESSED CENTER WHL ADAPT

KIT

MODELS

56 VL

56 VS

Summary of Contents for 56 VL












Search results

Summary of Contents for 56 VL

Reviews:

Related manuals for 56 VL

Brands by name

Popular brands

Henry Airtools 56 VL, General Safety And Maintenance Manual

Search results

Summary of Contents for 56 VL

Reviews:

Related manuals for 56 VL

Brands by name

Popular brands