manualshive.com logo in svg

HENNESSY INDUSTRIES Coats 4050A, Safety Instructions, Operating Instructions, Installation Instructions, Maintenance Instructions

The HENNESSY INDUSTRIES Coats 4050A user manual provides comprehensive Safety Instructions, Operating Instructions, Installation Instructions, and Maintenance Instructions for optimal performance and longevity. Download this manual for free from manualshive.com to ensure proper use and care of your equipment. Don't operate without reading the manual first.

Share
Download
background image

1601 J. P. Hennessy Drive, LaVergne, TN  USA  37086-3565   615/641-7533   800/688-6359

Manual Part No.: 8111144 00

HENNESSY INDUSTRIES INC.  Manufacturer of AMMCO

®

, COATS

®

and BADA

®

Automotive Service Equipment and Tools.

Revision:

02/97

Safety Instructions

Operating Instructions

Installation Instructions

Maintenance Instructions

READ these instructions before placing unit in
service KEEP these and other materials delivered
with the unit in a binder near the machine for
ease of reference by supervisors and operators.

4050A

Tire Changer

For servicing single piece automotive and
most light truck tire/wheel assemblies

®

Summary of Contents for Coats 4050A

















Reviews:

No comments

Related manuals for Coats 4050A

Brands by name

Popular brands

Load more brands