background image

Helmer Scientific i.Series

®

 - Platelet Agitator

Operation Manual 

360390/A

11

4  Specifications

4.1 

Operating Standards

These units are designed to operate under the following environmental conditions:

 

Indoor use only

 

Altitude (maximum): 2000 m

 

Ambient temperature range: 15 °C to 35 °C

 

Relative humidity (maximum for ambient temperature): 80% for temperatures up to 31 °C, decreasing linearly to 45% at 35 °C

 

Overvoltage category: I

 

Pollution degree: 2

 

Sound level is less than 60 dB(A).

 

Mains supply voltage: ±10% of nominal voltage

 

RF Emissions:  Group 1 - Class A

 

EMC Environment:  Basic

 Note

Power draw is measured in full-load Amperes during stand-alone operation and includes power supply.

Table 2. Electrical Specifications

PF15-Pro

PF48-Pro

PF96-Pro

Input Voltage and 

Frequency

Stand-alone (power supply): 100-240 VAC, 50/60 Hz 

Agitator Unit:  24VDC

Voltage Tolerance

±10% (AC input to power supply)

Power Draw

 < 16 Watts nominal

Power Source

24VDC AC/DC power supply (stand-alone) 

24VDC umbilical cable (configured with incubator)

Agitation Speed 

(cycles / minute)

40-80 CPM

Remote Alarm Capacity

1 A at 33 V (AC) RMS or 70 V (DC)

Table 3. Agitator Specifications

PF15-Pro

PF48-Pro

PF96-Pro

Height

13.5” (343 mm)

14.9” (379 mm)

14.9” (379 mm)

Width

16.0” (407 mm)

17.8” (453 mm)

32.8” (834 mm)

Depth

9.1” (232 mm)

14.9” (379 mm)

14.9” (379 mm)

Weight

33 lbs (15 kg)

50 lbs (23 kg)

80 lbs (37 kg)

CAUTION

•  The interface on the remote alarm monitoring system is intended for connection to the end user’s central alarm  

  system(s) that uses normally-open or normally-closed dry contacts.
•  If an external power supply exceeding 30 V (RMS) or 70 V (DC) is connected to the remote alarm monitoring system’s  

  circuit, the remote alarm will not function properly; may be damaged; or may result in injury to the user.

Summary of Contents for i Pro Series



















Reviews: