PROJECTION ALARM CLOCK WITH FM SCAN RADIO
USER MANUAL
KT3004
PLEASE READ THIS MANUAL COMPLETELY BEFORE OPERATING
THIS UNIT AND RETAIN THIS MANUAL FOR FUTURE REFERENCE
NOTES ON FCC COMPLIANCE
This equipment has been tested and found to comply with the limits for a radio receiver, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
WARNING
Changes or modifications to this unit not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
1
FEATURES AND CONTROL
Item
Description
Item
Description
1
Snooze/ Projector Button
7
ON/OFF Volume Control
n
o
tt
u
B
n
a
c
S
8
t
i
n
U
r
o
t
c
e
j
o
r
P
2
3
LCD display on demand
backlighting
9
Speaker
t
n
e
m
tr
a
p
m
o
C
y
r
e
tt
a
B
0
1
n
o
tt
u
B
e
d
o
M
4
l
o
rt
n
o
C
s
u
c
o
F
1
1
n
o
tt
u
B
t
e
S
5
a
n
n
e
t
n
A
e
ri
W
M
F
2
1
n
o
tt
u
B
t
e
s
e
R
6
GETTING STARTED
INSTALLING/REPLACING BATTERIES
This unit operates on three ‘AAA' (UM-4) size batteries (not included), bottom two for the FM radio and
the top one for the LCD alarm clock. All three are required for the Hello Kitty image projector and LCD
backlighting to work properly.
1. Loosen the screw of the battery compartment located at the back of the projector clock.
2. Remove old batteries (if any).
3. Following the polarity diagram shown inside the battery compartment, insert three fresh ‘AAA'
(UM-4) size alkaline batteries or Ni-MH rechargeable batteries (not included).
4. Close the battery compartment cover and secure the cover in place with screw.
IMPORTANT:
Be sure that the batteries are installed correctly. Wrong polarity may damage the
unit.
WARNINGS!
Batteries must be placed by an adult.
The use of good quality alkaline batteries is recommended.
Place batteries based on the polarity shown on the battery compartment.
Only use the recommended type of batteries.
Non rechargeable batteries are not to be recharged
Rechargeable batteries are only to be charged under adult supervision
Rechargeable batteries are to be removed before being charged.
DO NOT mix different types of batteries together.
DO NOT mix new and old batteries together.
If you do not use the product for an extended period of time, we recommend that you take out the
batteries. Remove exhausted batteries from the product. Battery leak may cause damage.
DO NOT short circuit the terminals of the battery.
DO NOT throw batteries into an open flame. They may explode.
Keep the packaging for future reference as it contain important information
2
ALARM CLOCK
Setting up
The LCD will display all icons and digits after batteries are placed into battery compartment. Then ‘AM
12:00’ as default time will be displayed on LCD display.
Switching among different modes
You can press ‘MODE’ to switch among four different modes:
1. Time mode – this is the default mode and it shows hour and minutes.
2. Alarm mode - set alarm wake up time.
3. Date mode - set the date, month and year.
4. Second mode - set the second of the clock.
Set the time
1. In time mode the default time is 12:00 AM. Press ‘SET’ and the ‘hour’ will be blinking and you can
set the hour.
2. Press ‘MODE’ button to reach the desired hour.
3. If ‘MODE’ is held down, it will advance the clock four hours per second.
4. Press ‘SET’ again and the ‘minute’ will be blinking and you can set the minute.
5. Press ‘MODE’ button to reach the desired minute.
6. If ‘MODE’ is held down, it will advance the clock four minutes per second. Press ‘SET’ again, and
the correct time should be displayed.
7. If the clock is idle for 6 seconds, it will assume setting is finished and go back to normal time display.
8. To switch from 12-hour display to 24-hour display, press SET when normal time appears. Press it
again to switch back.
3
AGES 8+
Front view
Back view
Meijer.com
