background image

PAGE 5

  2 

PARTS LIST 

IMPORTANT:  Read all instructions carefully. Assemble the Helix in accordance with the 
steps in the manual. Lay out all parts on the floor prior to assembly to make sure you have 
all the parts listed below. In case of discrepancy, please contact Customer Service at 
888-435-4926 or [email protected]

 

Item # 

Description 

Qty

 

Front Frame 

1

 

Rear Frame 

1

 

Center Upright Post 

1

 

Left Handlebar 

1

 

Right Handlebar 

1

 

Electronic Console Display 

1

 

Console Mounting Plate 

1

 

Front Upright Cover 

1

 

Rear Upright Cover 

1

 

10 

Rubber Gasket for Upright 

1

 

11 

Dome Shaped Cover 

1

 

12 

Pedal Frames and Covers 

2

 

13 

Base Cover 

1

 

14 

Seat Back 

1

 

15 

Seat Bottom 

1

 

16 

M10x65 Bolts 

4

 

17 

M10 Washer 

4

 

18 

M6x15 Bolts 

8

 

19 

M8x19 Bolts 

4

 

20 

M8 Washer 

16

 

21 

M8x20 Bolts  

4

 

22 

M8x15 Bolts  

4

 

23 

M8x58 Bolts  

2

 

24 

M8 Locknut 

3

 

25 

M8x92 Bolts  

1

 

26 

M4x15 Bolts  

4

 

27 

ST4x20 Bolt 

1

 

28 

S4 

1

 

29 

S5 

1

 

30 

S6 

1

 

31 

S10 S17 

1

HR1000-A5.indd   5

01/08/2017   16:05

Summary of Contents for HR 1000

















Reviews: