Heliocentris Energy Manager 1.3 Instruction Manual Download

Page: 36 / 78

Operating

Energy Manager 1.3 - Instruction Manual

Submenu

Menu item

Display

Description

I/C

SMS In

Number of received SMS

SMS Out

Number of outgoing SMS

Data

Inactive: no internet connection

Signal

Strength of signal

SIM

Missing, unknown or active

GSM

Not registered, searching

Not registered, not searching

Registered

GPRS

Not registered, searching

Not registered, not searching

Registered

Reset

Modem reset

I+C

RMS Status

Describes the communication between RAS
and EM

Status

Status of RMS: Connected or not connected

Last Error

No error or “name of the last error”

Pkgid Gen

Number Pkgid created

Pkgid Sent

Number PkgId sent to RMS

Tunnels

Number of tunnels to RMS

Legend:
*

Item is only displayed if the access level is service

I/C

Information/Command

Table 5-2 System submenu

5.1.3

Genset Submenu (Gen)

Menu item

Display

Description

I/C

OpMode

One of the
modes:

Operating mode of the genset
unit. The mode is also displayed
in the main menu if no error
occurred.

init

Software module initializes

active

Generator is running.

offline

Generator is offline and will not
be started by EM control
software.

standby

Generator is ready for operating
and will be started by EM, if
required.

error

An error was detected, generator

cannot run.

manual

A manual genset start was

detected, not triggered by EM

monitor

Genset unit is currently in
monitoring mode.

Summary of Contents for Energy Manager 1.3















































































Search results

Summary of Contents for Energy Manager 1.3

Reviews:

Related manuals for Energy Manager 1.3

Brands by name

Popular brands

Heliocentris Energy Manager 1.3, Instruction Manual

Search results

Summary of Contents for Energy Manager 1.3

Reviews:

Related manuals for Energy Manager 1.3

Brands by name

Popular brands