background image

12/03 Revision L1 #02833

Enerco Group, Inc., 4560 W. 160TH ST., CLEVELAND, OHIO 44135 • 216-881-5500

Improper installation, adjustment, alteration, service or maintenance can

cause injury or property damage. Refer to this manual. For assistance or additional
information consult a qualified installer, service agency or the gas supplier.

WARNING:

— WHAT TO DO IF YOU SMELL GAS

Open Windows

DO NOT

 try to light any appliance.

DO NOT

 use electrical switches.

DO NOT

 use any telephone in your house. Immediately call your local gas supplier from a

neighbor’s telephone. Follow the gas supplier’s instructions.

Do not

 touch any electrical switch; do not use any phone in your building.

Installation and service must be performed by a qualified installer, service agency or the gas
supplier.

If you cannot reach your gas supplier, call the Fire Department.

Gas-Fired, Low-Intensity Infrared Heaters
approved for residential Garage/Commercial Applications

enerRADIANT

®

FOR YOUR SAFETY:
Do not store or use gasoline or other flammable vapors and liquids in the vicinity of
this or any other appliance.

WARNING: If the information in these instructions are not followed exactly, a fire or
explosion may result causing property damage, personal injury or loss of life.

HST35, HST45

READ INSTRUCTIONS CAREFULLY:

 Read and follow all instructions.

Place instructions in a safe place for future reference. Do not allow
anyone who has not read these instructions to assemble, light, adjust or
operate the heater.

MODEL

OPERATING INSTRUCTIONS AND OWNER’S MANUAL

HEATSTAR

Summary of Contents for enerradiant HST35

























Reviews: