background image

29

Heat & Glo  •  MEZZO1000-AUB, MEZZO1300-AUB, MEZZO1300ST-AUB, MEZZO1600-AUB Owner’s Manual  •  2304-974 Rev. C  •  3/16  

Service Parts

Beginning Manufacturing Date: Feb 2016 

Ending Manufacturing Date: Active

#13 LED Light Assembly

MEZZO1300-AUB

1300mm Gas Fireplace - DV

IMPORTANT: THIS IS DATED INFORMATION

. Parts must be ordered from a dealer or distributor. 

Hearth and Home 

Technologies does not sell directly to consumers

. Provide model number and serial number when requesting service parts 

from your dealer or distributor.

ITEM

DESCRIPTION

COMMENTS

PART NUMBER

1

Non-combustible Board, Top

2304-460

2

Standoff, Top

Qty 4 req

2300-282

3

Non-combustible Board, Side

Qty 2 req

2304-461

4

Bottom glass

2300-018

5

Burner

2300-007

6

Pilot Assembly

See Following Page

7

Shield, Pilot

2300-195

8

Glass Assembly

GLA-48-HNG

9

Shield., Bottom Glass

2300-179

10

Panel, Bottom

2304-147

11

Rock Tray

2300-151

12

Rail, Burner

Qty 2 req

2300-338

13

LED Light Assembly

SRV2304-014

13.1

LED 12V Power Supply

2273-308

13.2

Cord Assembly

2101-084

13.3

AUX300CE

2166-340

Additional service part numbers on following page.

3/16

13.1

13.2

13.3

1

2

3

4

5

6

7

8

9

10

11

12

Summary of Contents for MEZZO1000-AUB




































Reviews: