background image

Heat & Glo  •  ST-42TVFL-IPI  •  455-902 Rev. C  •  12/07

Model:

ST-42TVFL-IPI

1

Owner’s Manual

Installation and Operation

• Do not store or use gasoline or other flamma-

ble vapors and liquids in the vicinity of this or
any other appliance.

• What to do if you smell gas

- Do not try to light any appliance

- Do not touch any electrical switch. Do not

use any phone in your building.

- Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s
instructions.

- If you cannot reach your gas supplier, call

the fire department.

• Installation and service must be performed by

a qualified installer, service agency, or the gas
supplier.

WARNING:  If the information in these

instructions is not followed exactly, a fire
or explosion may result causing proper-
ty damage, personal injury, or death.

HOT SURFACES

!

Glass and other surfaces are hot during

operation AND cool down.

Hot glass will cause burns.

DO NOT

 touch glass until it is cooled

NEVER allow children to touch glass

Keep children away

WARNING

• CAREFULLY SUPERVISE children in same room as fireplace.

• Alert children and adults to hazards of high temperatures.

High temperatures may ignite clothing or other flammable

materials.

• Keep clothing, furniture, draperies and other flammable

materials away.

DO NOT DISCARD THIS MANUAL

CAUTION

Important operating
and maintenance
instructions included.

This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must
be installed in accordance with the manufacturer’s instruc-
tions and the manufactured home construction and safety
standard, 

Title 24 CFR, Part 3280 

or 

Standard for Installa-

tion in Mobile Homes, CAN/CSA Z240MH.

This appliance is only for use with the type(s) of gas indi-
cated on the rating plate.

Installation and service of this appliance should be
performed by qualified personnel. Hearth & Home
Technologies suggests NFI certified or factory-trained
professionals, or technicians supervised by an NFI
certified professional.

In the Commonwealth of Massachusetts installation must

be performed by a licensed plumber or gas fitter.

See Table of Contents for location of additional

Commonwealth of Massachusetts requirements.

Read, understand and follow
these instructions for safe
installation and operation.

Leave this manual with
party responsible for
use and operation.

DO NO

DO NO

DO NO

DO NO

DO NO

TTTTT

DISCARD

DISCARD

DISCARD

DISCARD

DISCARD

This appliance has been supplied with an integral barrier

to prevent direct contact with the fixed glass panel. DO

NOT operate the appliance with the barrier removed.

Contact your dealer or Hearth & Home Technologies if the

barrier is not present or help is needed to properly install one.

Í

Summary of Contents for ST-42TVFL-IPI




























Reviews: