manualshive.com logo in svg

Heat & Glo LifeStyle ST-38HV-AU, Installation And Operation Instructions Manual

Share
Download
Heat & Glo LifeStyle ST-38HV-AU Installation And Operation Instructions Manual Download Page 1

1

MODEL: ST-38HV-AU

 

AUSTRALIAN GAS ASSOCIATION APPROVED

APPROVAL NUMBER 6027

THIS MANUAL MUST BE USED FOR INSTALLATION AND RETAINED

BY HOMEOWNER FOR OPERATION AND MAINTENANCE.

675-900D  11/05

INSTALLATION AND OPERATION

INSTRUCTIONS

This product may be covered by one or more of the following patents: (United States) 4593510, 4686807, 4766876, 4793322, 4811534, 5000162, 5016609, 5076254, 5113843, 5191877, 5218953, 5263471,
5328356, 5341794, 5347983, 5429495, 5452708, 5542407, 5601073, 5613487, 5647340, 5688568, 5762062, 5775408, 5890485, 5931661, 5941237, 5947112, 5996575, 6006743, 6019099, 6048195,
6053165, 6145502, 6170481, 6237588, 6296474, 6374822, 6413079, 6439226, 6484712, 6543698, 6550687, 6601579, 6672860, 6688302B2, 6715724B2, 6729551, 6736133, 6748940, 6748942, 6769426,
6774802, 6796302, 6840261, 6848441, 6863064, 6866205, 6869278, 6875012, 6880275, 6908039, 6919884, D320652, D445174, D462436; (Canada) 1297749, 2195264, 2225408, 2313972; (Australia)
780250, 780403, 1418504 or other U.S. and foreign patents pending.

HEAT & GLO, a brand of Hearth & Home Technologies Inc.

20802 Kensington Blvd., Lakeville, MN 55044, USA • (952) 985-6000

Summary of Contents for ST-38HV-AU




































Reviews:

No comments

Brands by name

Popular brands

Load more brands