background image

BLUE FLAME VENT-FREE

NATURAL GAS SPACE

HEATER

OWNER

S OPERATION AND INSTALLATION MANUAL

HB20TN-1

HB30TN-1

HB20MN-1

HB30MN-1

Table  of  Contents

        WA R N I N G :     I m p r o p e r       i n s t a l l a t i o n ,
adjustment, alteration, service  or  mainte-
nance can  cause  injury  or  property  damage.
Refer  to  this  manual  for  correct  installation  and
operational  procedures.  For  assistance  or
additional  information  consult  a  qualified
installer,  service  agency,  or   gas  supplier.

This  appliance  may  be  installed  in  an  aftermar-
ket*  permanently  located, manufactured
(mobile) home, where  not  prohibited  by  local
codes.
This appliance  is  only  for  use  with  the  type  of
gas  indicated  on  the  rating  plate. This
appliance  is  not  convertible  for  use  with  other
gases.

*Aftermarket: Completion  of  sale, not  for  purpose  of
resale,  from  the  manufacturer.

Do  not  store,  or  use  gasoline  or  other  flammable
vapors  and  liquids  in  the  vicinity  of  this  or  any
other  appliance.
WHAT  TO  DO  IF  YOU  SMELL  GAS

 

Do  not  try  to  light  any  appliance.

 

Do   not   touch   any   electrical   switch;  do  not

       use  any  phone  in   your  building.

 

Immediately   call   your  gas  supplier  from  a

       neighbor’s   phone.   Follow   the   gas  supplier’s
       instructions.

 

If   you   cannot  reach  your  gas  supplier, call

       the  fire  department.
Installation  and  service  must  be  performed  by  a
q u a l i f i e d     i n s t a l l e r ,   s e r v i c e     a g e n c y    o r     g a s
supplier.

Important Safety Information.................................2

Product  Features.....................................................3

Proper Ventilation & Fresh Air...............................4

Installation................................................................6

Operating Your  Heater...........................................10

Cleaning & Maintenance.......................................13

Trouble  Shooting...................................................14

Specifications..........................................................17

Parts  List.................................................................19

Warranty Information.............................................22

    WARNING:   This  is  an  unvented gas-fired
heater.  It  uses  air  (oxygen) f r o m     t h e     r o o m
i n     w h i c h     i t     i s  installed.  Provisions  for
adequate combustion  and  ventilation  air  must
b e     p r o v i d e d .     R e f e r     t o    A i r     F o r  Combus-
tion  and  Ventilation section on  page  4  of  this
manual.

      WA R N I N G :    I f     t h e     i n f orm a t i o n     i n  this
manual  is  not  followed  exactly, a     f i r e     o r
e x p l o s i o n     m a y     r e s u l t  causing  property
damage,  personal injury,  or  loss  of  life.

WATER VAPOR: A BY-PRODUCT OF UNVENTED
ROOM HEATERS
Water vapor is a by-product of gas combustion. An
unvented room heater produces approximately one
(1) ounce (30ml) of water for every 1,000 BTU’s
(.3KW’s) of gas input per hour. Refer to page 3.

Installer: Please leave these instructions with the
consumer.

Consumer: Please retain these instructions for fu-
ture use.

A Division of Empire Comfort Systems,Inc.

                                   918 Freeburg Avenue

Phone : 618-233-7420 or 1-800-851-3153

Fax : 618-233-7097 or 1-800-443-8648

Belleville,IL 62220

Summary of Contents for HB20MN-1

























Reviews: