Hearth Technologies Heat-N-Glo 8000TVC Installer Manual Download Page 1

- Do not store or  use gasoline or other flammable

vapors and liquids in the vicinity of this or any

other appliance.

-

What to do if you smell gas

• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
• Immediately call your gas supplier from a

neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the

fire department.

- Installation and service must be performed by a

qualified installer, service agency, or the gas

supplier.

Heat-N-Glo

Model:

8000TVC

Installers Guide

WARNING: IMPROPER

INSTALLATION, ADJUSTMENT,

ALTERATION, SERVICE OR

MAINTENANCE CAN CAUSE INJURY

OR PROPERTY DAMAGE. REFER TO

THIS MANUAL. FOR ASSISTANCE OR

ADDITIONAL INFORMATION

CONSULT A QUALIFIED INSTALLER,

SERVICE AGENCY, OR THE GAS

SUPPLIER.

258-900C  10/99

READ THIS MANUAL BEFORE INSTALLING

OR OPERATING THIS APPLIANCE. THIS

INSTALLERS GUIDE 

MUST BE LEFT WITH

THE APPLIANCE FOR FUTURE REFERENCE.

Please contact your Heat-N-Glo dealer with

any questions or concerns. For the number

of your nearest Heat-N-Glo dealer, please

call 612-985-6000.

Printed in U.S.A.    Copyright 1999,

Heat-N-Glo, a division of Hearth Technologies Inc.

20802 Kensington Blvd., Lakeville, MN 55044

This product is covered by one or more of the following patents: (United States) 4,112,913; 4,408,594; 4,422,426; 4,424,792; 4,520,791; 4,793,322;
4,852,548; 4,875,464; 5,000,162; 5,016,609; 5,076,254 5,191,877; 5,218,953; 5,328,356; 5,429,495; 5,452,708; 5,542,407; 5,613,487; (Australia)
543790;586383; (Canada) 1,123,296; 1,297,746; 2,195,264; (Mexico) 97-0457; (New Zealand) 200265; or other U.S. and foreign pate nts pending.

Underwriters

 Laboratories Listed

WARNING

IF THE INFORMATION IN THESE

INSTRUCTIONS IS NOT

FOLLOWED EXACTLY, A FIRE OR

EXPLOSION MAY RESULT

CAUSING PROPERTY DAMAGE,

PERSONAL INJURY, OR DEATH.

All manuals and user guides at all-guides.com

all-guides.com

Summary of Contents for Heat-N-Glo 8000TVC


























Reviews: