HDX E3590137OBH4THD Use And Care Manual Download Page 1

 

 

 HOMEDEPOT.COM 

 

 

Please contact 1-800-514-6729 for further assistance. 

 

Use and Care Guide 

 

4-Tier Shelving Unit 

Item #

  

564184 

            1001078103 
            1001298072 
Model #

 

E3590137OBH4THD 

              E3590137OBK4THD 
              E3590137OBW4THD

 

 

 

 

PACKAGE CONTENTS 

HARDWARE INCLUDED 

 

 

 

 

 

 

 

A – Shelf x 4 

B – Tapered 

sleeve x 32 

+ 2 extra 

C – Bottom pole with 

pre-installed leveler x 4 

D – Top pole x 4 

AA –  

Washer x 2 

BB –  

Anchor x 2 

CC –  

Screw x2 

 

Safety Information  

 

Read and understand this manual before assembly. 

Before you begin, inspect each part and compare to the Package Contents list. 
If any part appears missing or damaged, do not assemble and use this product. 
Contact Customer Service at 1-800-514-6729. 

1. 

Two adults are recommended for ease of assembly. Use care when handling. 

2. 

Assemble on a soft surface, such as carpet, to avoid scratching the finish. 

 

 

CAUTION:

 Do not allow children to play or 

climb on the product.

 

 

 

CAUTION:

 Place the unit on a level surface to 

avoid a tipping hazard.

 

 

 

CAUTION:

 Each shelf holds up to 350 lbs, 

evenly distributed. Do not overload.

 

 

Assembly 

Assembling the posts 

Installing the bottom shelf 

 

 

Before you begin, discard the black 
circular pieces found when unpacking this 
product. They are for shipping purposes 
only. 

 

Screw the bottom pole (C) to the top pole 
(D). Repeat for the remaining poles. 

 

 

 

Determine the desired position of the shelf (A). 
Ensure that it is no more than 6 in. from the 
floor. 

 

Place two tapered sleeves (B) into the 
appropriate groove on each pole assembly. 
Ensure the “UP” arrow faces up. Ensure each 
sleeve is the same height to ensure the shelf 
is level when installed. 

 

Place the shelf (A) on its side and slide each 
pole assembly through the bottom of the shelf 
(A) until snug. After all pole assemblies are in 
place, position the unit in the upright position. 

 

Push down on each corner of the shelf (A), 
ensuring the corners of the shelf (A) slip fully 
in the locked position over the sleeves (B). 
 

 

 

Adding shelves 

Adjusting the levelers 

Mounting to the wall 

 

Determine the position of the second 
shelf. Place the tapered sleeves (B) onto 
the pole assemblies and ensure that the 
sleeves are level with each other. 

 

Slide the shelf (A) down from the top of 
the pole assemblies and onto the tapered 
sleeves (B). 

 

Push each corner of the shelf (A) down 
until it locks into position over the sleeves 
(B). Repeat for the remaining shelves (A). 

 

 

Move the assembly to the desired 
location. 

 

If needed, adjust the levelers on the 
bottom of the poles (C) to ensure the 
shelving unit is level. Rotate the levelers 
counterclockwise to raise the poles, and 
clockwise to lower the poles. 

 
 

 

 

 

WARNING:

 This step is required to ensure the 

stability of the shelves.

 

 

 

Mark the locations of the mounting holes with a 
pencil using the top shelf (A) as a guide. Drill pilot 
holes at the marked locations using a 1/4 in. bit, 
and insert the wall anchors (BB) into the holes. 

 

Secure the top of the shelf (A) to the wall by 
inserting screws (CC) with washers (AA) through the 
shelf (A) and into the wall anchors (BB). 

 

 

 

D

C

6 in.

B

A

B

B

A

C

A

CC

BB

AA

NSF

®

Reviews: