1
www.observint.com
HDV_B8V_CQ
190701
Installation
Before installation:
•
Make sure that the device is in good condition and all the assembly parts are included.
•
Check the specification of the products for the installation environment.
•
Make sure that the wall or the ceiling is strong enough to withstand 3 times the weight of the camera.
•
To avoid fire or shock hazard, use only UL listed power supplies. Verify that the power supply will
provide the rated voltage and wattage for the camera. See the
Specifications
section.
Step 1. Mounting the camera
A B8V camera can be mounted directly to a wall or ceiling. The surface should support at least three times
the weight of the camera. The drop cables of this camera are normally routed through mounting surface,
but can be routed through the cable channel.
NOTE
If mounting the camera on a wall, ensure that the cable channel in the mounting base is down.
If mounting the camera on a ceiling, orient the mounting base so that the cable channel is pointing
away from any source of water, dust, and other contaminates.
1.
Acquire the kind of fasteners that will work best for mounting the camera to the ceiling or wall. The
mounting hardware provided with the camera will work well withe many types of surfaces.
2.
Using the camera or the template provided, mark the locations of the mounting screw holes. If
routing the drop cables through the surface behind the mounting bracket, also mark a 3/4” hole for
the drop cables.
3.
Drill holes in the surface of the mounting location to accommodate the camera fasteners and the
drop cables.
4.
Route the video and 12 Vdc power extension cables from recorder and power source to the camera
mounting location and out through the hole drilled for the camera drop cables.
5.
Connect the video and power extension cables to the camera drop cables. Verify that the power
cable connector polarity matches the polarity of the power drop cable.
WARNING
!
Drop cable connectors are not waterproof.
Failure of the power or video
drop cable connector due to moisture or another contaminant is considered an
installation error, which voids the warranty. Seal all connectors adequately.
6.
Set the HD format select switches on the drop cable for the video encoding you prefer to use. See
the drop cables photo to the left.
7.
Route the drop cable through the hole in the mounting surface, then attach the camera assembly to
the surface using the appropriate fasteners.
8.
Apply power to the camera through the 12 Vdc power cable.
9.
Verify that you can see video from the camera at the recorder.
Step 2. Camera adjustments
1.
While observing video from the camera, loosen the mounting bracket pan, tilt and rotation
adjustment lock screws.
2.
Point the camera at your surveillance target, and then tighten mounting bracket adjustment screws
to hold the camera in position.
B8V 8 MP 4-in-1 HD Varifocal 150 ft IR
Bullet Camera Quick Installation Guide
This 8 MP HD-TVI security camera captures sharp high definition video images with its high-performance
CMOS sensor and 2.8 ~ 12 mm varifocal lens. This camera features:
•
3840 × 2160 (8 MP) progressive scan CMOS sensor
•
2.8 mm ~ 12 mm varifocal lens providing a 105.94°(W) ~ 29.76°(T) horizontal field of view
•
Switch selectable TVI, AHD, CVI or CVBS video signal format (4-in-1)
•
IR range up to 150 feet
•
Flip and Rotation image adjustments
•
IP66 weatherproof rating
Camera body
Light sensor
Lens
Focus adjust
Zoom adjust
Sun shield
Cable channel
Adjustable
mounting
bracket
B8V camera assembly
Cap
HD Video BNC connector
12 Vdc connector
HD format select switches
Format
TVI
AHD
CVBS
CVI
Switch
1
2
1
2
1
2
1
2
Setting
Down
Down
Down
Up
Up
Up
Up
Down
Camera drop cables
What’s in the box
•
Camera assembly
•
Mounting hardware
•
L-wrench
•
Drill template
•
Quick Installation Guide
Tools you need
To install the camera, you will need:
•
12 Vdc power source. See
Specifications
for wattage requirement.
•
Tools and additional fasteners (may be required) for mounting the camera
•
Phillips #2 screwdriver
•
Video and 12 Vdc power extension cables
