manualshive.com logo in svg

HCC Technology POS80B, Technical Manual, Page: 67 / 71

Share
Download
HCC Technology POS80B Technical Manual Download Page 67

Thermal Printer Technical Manual

 

 

 
 

 

                         

                                                         

67

 

 

Since this data is character data, however, it can be easier to handle and transmit 
than binary data. 

  [Example]             

! 0 200 200 210 1 
EG 2 16 90 45 F0F0F0F0F0F0F0F00F0F0F0F0F0F0F0F 
F0F0F0F0F0F0F0F00F0F0F0F0F0F0F0F 
PRINT

 

 
 

 

6.

 

Appendix A: CODE128 code 

 

A.1 CODE128 code 

 
CODE 128 code passing alternate character sets A,B character set and character set C,capable of 
128 and 100 ASCII characters from 00 to 99 digits, and some special characters are encoded.Each 
character set encoding of characters is as follows: 
·Character Set A: ASCII characters 00H to 5FH 
·Character Set B: ASCII characters 20H to 7FH 
·Character Set C: 00 ~ 99 of 100 digital 
CODE 128 code can also be encoded for the following special characters: 
· SHIFT character 
"SHIFT"to make the character behind the bar code symbol SHIFT convert the first character from 
the character set A to character set B,or B to convert from character set to character set A,began 
to recover from the second character to SHIFT previously used character set."SHIFT"character set 
only character set conversion between A and B used in the character,it does not make the current 
coded character set C character enters or exits the state. 
·Character set selection character(CODE A, CODE B, CODE C) 
These characters can convert it back to a character set encoding of characters A, B or C. 
·Function character(FNC1, FNC2, FNC3, FNC4) 
These features are useful depends on the application soft ware breaks.In the character set C, only 
FNC1 available. 

Summary of Contents for POS80B








































































Reviews:

No comments