manualshive.com logo in svg

HCC Technology POS80B, Technical Manual, Page: 51 / 71

Share
Download
HCC Technology POS80B Technical Manual Download Page 51

Thermal Printer Technical Manual

 

 

 
 

 

                         

                                                         

51

 

 

                        n = 1 Traditional Chinese models. 
 

FS S n1 n2    Set left- and right-side Chinese character spacing 

[Name] 

          Set left- and right-side Chinese character spacing 

[Format]

   

ASCII   

 

FS     

S     

n1    n2 

Hex   

 

1C     

53     

n1  n2 

Decimal    

28     

83     

n1    n2 

[Range] 

     

0 ≤ n1 ≤ 255 

                        0 ≤ n2 ≤ 255 

[Description] 

   

Set left- and right-side Chinese character spacing n1 and n2, respectively. 
When the printer model used supports GS P, the left-side character spacing is [n1 × horizontal or 
vertical motion units], and the right-side character spacing is [n2 × horizontal or vertical motion 
units]. 

[Notes] 

When  double-width  mode  is  set,  the  left-  and  right-side  character  spacing  is  twice  the  normal 
value. 
The  horizontal  and  vertical  motion  units  are  set  by  GS  P.  The  previously  specified  character 
spacing does not change, even if the horizontal or vertical motion unit is changed using GS P. 
In standard mode, the horizontal motion unit is used. 
In page mode, the horizontal or vertical motion unit differs in page mode,depending on starting 
position of the printable area as follows: 
When  the  starting  position  is  set  to  the  upper  left  or  lower  right  of  the  printable  area,  the 
horizontal motion unit (x) is used. 
When the starting position is set to the upper right or lower left of the printable area, the vertical 
motion unit (y) is used. 
The maximum right-side spacing is approximately 36 mm. Any setting exceeding the maximum is 
converted to the maximum automatically. 

[Default]

          n1 = 0, n2 = 0 

[Reference]

      GS P 

 

FS W n    Turn quadruple-size mode on/off for Chinese characters 

[Name] 

          Turn quadruple-size mode on/off for Chinese characters 

[Format]

   

ASCII   

 

FS     

W     

n 

Hex   

 

1C     

57     

n 

Decimal    

28     

87     

n 

[Range]   

        0 ≤ n ≤ 255 

[Description]

    

Turn quadruple-size mode on or off for Chinese characters. 
When the LSB of n is 0, quadruple-size mode for Chinese characters is turned off. 
When the LSB of n is 1, quadruple-size mode for Chinese characters is turned on. 

[Notes] 

Only the lowest bit of n is valid. 
In  quadruple-size  mode,  the  printer  prints  the  same  size  characters  as  when  double-width  and 
double-height modes are both turned on. 
When  quadruple-size  mode  is  turned  off  using  this  command,  the  following  characters  are 
printed in normal size. 
When some of the characters on a line are different in height, all the characters on the line are 
aligned at the baseline. 

Summary of Contents for POS80B








































































Reviews:

No comments