HBM WTX120, Operating Manual

Page: 229 / 550

WTX120
Navigation Pilot
Unload Scale
Standard
WTX120 V1.0 (Master = W1)
< 3 seconds
Switch from Master WTX120 to slaves
< 3 seconds < 3 seconds
hold + push to skip
+
Weight Storage Logbook Software ID
WTX120 Remote Control (slaves = WA, WB, ...)
Data Word Monitor
Products
hex / dez
error protocoll,
only info Mastermode
note: alternative
access
binär
Mode: Info
(zero offset) Mode: Adapt
(several
filter settings)
General
Config.
Analog out Config.
Fieldbus Config.
Remote Ctrl Config.
Digital IO
Config. Scale
Com2 (SIM2) Com1 (SIM1) Com0 (Eth)
Digital IO Factory defaults Limit switches General Setup Calibration
Calibrate Scale 1
Select Group 1 – 9
Config. Test Reset Network Backup General Interface
Mastermode Application Service Mode
Date: Entry
Time: Entry
Filler configuration;
only available
in filler application
access
if no sensor
is connected
exception: back to „Select Group 1 – 9“ with
not with the INFO-Button
only available in
standard application
only available if WTX slaves are in the same
network and correctly assigned in
Service Mode / Config. / Config. Remote Ctrl.
note: if „S1“ activated
only access,
no changes possible
Search Date
Id-No.
Weight not found
Language
Keyboard
Time Zone (1)
Time Zone (2)
Date (format only)
Time (format only)
Country Code
Decimal char.
Approval signs
Tare mode
Cont. out.
Light off (Min.)
Power off (Min.)
Serial No.
Test
G1
Reset
Parameters?
Reset
Approved Wgt
...
Aout 1: Mode
Aout 1: Output
Aout 1: Calibration
PROFINET
EtherNet-IP
Modbus-TCP
Profibus DP
+ address
IP address 1
IP address 2
2 Calibration 3 Linearization 4 Zero Adjust 5 Adaption 6 High
Resolution
7 Reset 8 Calculation
Span
9 W&M Info 1 Scale
Parameters
Geo Value
Calibrate zero?
Calibrate load?
New Fixpoint 1? Motion Windo
Motion Counter
Filter Size
Auto zero range
...
Power up zero
With Taring?
Underload
Update Rate
Weight Reset Parameters? Calibrate Zero?
Zero (mV/V)
LC-Cap. (kg)
No. of LCs
mV/V of LC1
W&M Setup ok
IP
Mask
Gate
DNS
NTP
FTP pwd
PanelX access
Set PanelX password
Update SSL cert
Start auto ping
Terminal No.
Backup or
Restore
from USB Application
note: after
change restart
required!
Language
LS1 – LS4 Source
LS1 – LS4 Mode
Input 1 – 4
Output 1 – 4
Load fact. Def.
Settings
Baud
Databits
Parity
Ctrl.
Protcl.
Baud
Databits
Parity
Ctrl.
Protcl.
Port
Protocol
Entry field INFO level
Three diffrent possible entries
Map symbology
Subsequent field INFO level
Related fields on INFO level
Enter password / Unload Scale
Mastermode
Click INFO button
Click respective grey button
Notes
Triple Range Dual Range Single Range
High Cap.
High Int.
Low Cap.
Low Int.
Unit
High Cap.
High Int.
Mid Cap.
Mid Int.
Low Cap.
Low Int.
Unit
Three Intervals Two Intervals One Interval
High Cap.
High Int.
Low Cap.
Low Int.
Unit
Capacity
Interval
Unit
High Cap.
High Int.
Mid Cap.
Mid Int.
Low Cap.
Low Int.
Unit
Three Intervals T+ Two Intervals T+
High Cap.
High Int.
Low Cap.
Low Int.
Unit
High Cap.
High Int.
Mid Cap.
Mid Int.
Low Cap.
Low Int.
Unit
3_ ...
2_ ...
1_...
ID: ...
Password
Enter service
password Enter service
password
Password
1 Entry
Service
Mode
2 Entry
Setup-
Level
3 Entry
Supervisor
Mode
measure and predict with confidence
Target weight
...