HBM WTX110, Operating Manual

Page: 286 / 436

Unload Scale
Standard
WTX110 V#.#.#
< 3 seconds < 3 seconds
Weight Storage Logbook Software ID Products
error protocoll,
only info Mastermode
note: alternative
access
Mode: Info
(zero offset) Mode: Adapt
(several
filter settings)
General
Config.
Analog out Config.
Digital IO
Config. Scale
Com6 (DWB) Com1 (SIM1) Com0 (Eth)
Digital IO Print Formats Limit switches General Setup Calibration
Calibrate Scale 1
Select Group 1 – 9
Config. Test Reset Network Backup General Interface
Mastermode Application Service Mode
Date: Entry
Time: Entry
…
Brightness
Password
Target weight
...
Filler configuration;
only available
in filler application
note: only if
ALI available
only info
parameter
exception: back to „Select Group 1 – 9“ with
not with the F1 button
note: adapted parameters
must be saved to be valid!
only available in
standard application
note: only
calibration
note: only if
ALI available
note: ETH
or USB option
required
note: if „W1“ jumper
is in position 1
only access,
no changes possible
Search Date
Id-No.
Weight not found
Language
Keyboard
Time Zone (1)
Time Zone (2)
Date (format only)
Time (format only)
Country Code
Decimal char.
Approval signs
Tare mode
Cont. out.
Light off (Min.)
Power off (Min.)
Power Supply
Serial No.
Digital IO
Serial IO
ADM
HBM
None
PIM
Modbus TCP
SIO
None
Scale Reset Service
Mode Parameters?
Reset
Approved Wgt
Non
DAU15
...
Aout 1: Mode
Aout 1: Output
Aout 1: Calibration
2 Calibration 3 Linearization 4 Zero Adjust 5 Adaption 6 High
Resolution
7 Reset 8 Calculation
Span
9 W&M Info 1 Scale
Parameters
Geo Value
Calibrate Zero?
Calibrate Load?
New Fixpoint 1? Motion Window
Motion Counter
Filter Size
Auto Zero Range
...
Incline Switch
PowerUp Zero
With Taring?
Underload
Update Rate
1. Connect Sensor
2. go to “Calibration”\“1 Scale Parameters”
and enter load cell parameters like Capacity, Interval, Unit
3. Perform Calibration
- with Calibration Weight go to “2 Calibration”
- without Calibration Weight go to “8 Calculation Span”
4. Enter further parameters like Dual Range, Linearization, etc.
5. Save Calibration Parameters
Weight Reset Parameters? Calibrate Zero?
Zero (mV/V)
LC-Cap. (kg)
No. of LCs
mV/V of LC1
W&M Setup ok
IP
Mask
Gate
DNS
NTP
FTP pwd
PanelX access
Access number
Set PanelX password
Update SSL cert
Start auto ping
Terminal No.
Backup or
Restore
from USB Application
note: after
change restart
required!
Language
LS1 – LS4 Source
LS1 – LS4 Mode
Input 1 – 4
Output 1 – 4
Ticket Weight
Total Weight
Ticket Count
Total Count
Factory defaults
Load application
Baud
Databits
Parity
Ctrl.
Protcl.
Baud
Databits
Parity
Ctrl.
Protcl.
Port
Protocol
Entry field F1 button level
Two different possible entries
Map symbology
Subsequent field F1 button level
Related fields on F1 button level
Enter password / Unload Scale
Mastermode
Click F1 button
F1
F2 F3 F4 F5
Click respective grey button
Notes
Triple Range Dual Range Single Range
High Cap.
High Int.
Low Cap.
Low Int.
Unit
High Cap.
High Int.
Mid Cap.
Mid Int.
Low Cap.
Low Int.
Unit
Three Intervals Two Intervals One Interval
High Cap.
High Int.
Low Cap.
Low Int.
Unit
Capacity
Interval
Unit
High Cap.
High Int.
Mid Cap.
Mid Int.
Low Cap.
Low Int.
Unit
Three Intervals T+ Two Intervals T+
High Cap.
High Int.
Low Cap.
Low Int.
Unit
High Cap.
High Int.
Mid Cap.
Mid Int.
Low Cap.
Low Int.
Unit
3_ ...
2_ ...
1_...
ID: ...
MAC-/IP-Address
M:
IP:
Password
Enter service
password
1 Service
Appl.
Master
2 Entry
Supervisor
Mode
measure and predict with confidence
Quick Start Guide for Calibration Setup
WTX110
Navigation Pilot