Hawkeye Mfg AGCO RoGator A Series Installation Manual Download | Manualshive

Page: 21 / 54

background image

CHAPTER

4

Nozzle Body and Nozzle Control Valve Installation: Hawkeye® 2 Nozzle Body Installation

17

CHAPTER 4

NOZZLE BODY AND NOZZLE

CONTROL VALVE

INSTALLATION

HAWKEYE® 2 NOZZLE BODY INSTALLATION

After completing the steps in Chapter 3,

Installation Preparation

, install the provided nozzle bodies and nozzle

control valves.

BEST PRACTICES AND RECOMMENDATIONS

• Do not connect battery leads until all cables are installed and connected.
• If a dual outlet nozzle body is installed on the boom, always mount the Hawkeye® 2 nozzle control valve to the

closest port to the boom tube to avoid higher stress on the nozzle body.

HYPRO NOZZLE BODY INSTALLATION

NOTE:

For some Hypro

kits, the standard Hypro nozzle bodies will need to be replaced with left-handed

versions of the 5-way nozzle body in order to prevent interferences with the NCV2.

FIGURE 1. Valve Face O-Ring and Nozzle Control Valve Installed

1. Locate included Hypro 5-way, left-handed nozzle bodies in the kit.

Valve Body Face O-Ring

(Place O-Ring Here)

Nozzle Body

Purple O-Ring

«
...
19
20
21
22
23
...
»

Summary of Contents for AGCO RoGator A Series























































Reviews:

No comments

Related manuals for AGCO RoGator A Series

Brand: Unex Pages: 24

BAKER HUGHES DPS 5000 Series

Brand: GE Pages: 36

Brand: Oemtools Pages: 8

Brand: U.S. General Pages: 5

Brand: Panasonic Pages: 268

Brand: Samsung Pages: 133

Brand: Banner Pages: 2

Brand: AA Products Pages: 6

Brand: Front Runner Pages: 5

Brand: Takex Pages: 4

Brand: Lincoln Electric Pages: 32

MOLLE PANELS RAM 2500

Brand: PUTCO Pages: 4

Brand: Westfalia Pages: 18

Brand: BrandMotion Pages: 8

Brand: SICK Pages: 119

Brand: AMP Research Pages: 12

Half Size Trunk Box Organizer C-TBO-CV

Brand: Havis-Shields Pages: 1

990E0-54P56-000

Brand: Suzuki Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands