RX50X-50 5.25” COAXIAL SPEAKERS
INSTALLATION GUIDE
HAWG WIRED
PAGE 1
NEWARK, CA
R
R
R
X
X
X
5
5
5
0
0
0
x
x
x
-
--
5
5
5
0
0
0
S
S
S
P
P
P
E
E
E
A
A
A
K
K
K
E
E
E
R
R
R
S
S
S
K
K
I
I
T
T
C
C
O
O
N
N
T
T
E
E
N
N
T
T
S
S
2 – RX50X-50 5.25” COAXIAL SPEAKERS
NOTE: (RX502-50 = 2 OHM, RX508-50 = 8 OHM)
I
I
N
N
S
S
T
T
A
A
L
L
L
L
A
A
T
T
I
I
O
O
N
N
I
I
N
N
S
S
T
T
R
R
U
U
C
C
T
T
I
I
O
O
N
N
S
S
1.
TURN THE IGNITION SWITCH OFF.
2.
REMOVE THE FRONT FAIRING COVER, NOTING WHICH HOLE EACH SCREW COMES FROM.
TIP: REFER TO MANUFACTURER INSTRUCTIONS IF NECESSARY, AND DON’T FORGET TO COVER YOUR FENDER.
3.
DISCONNECT AND REMOVE EXISTING SPEAKERS, SPEAKER RINGS, AND GRILLS.
NOTE: SOME SCREW LENGTHS MAY VARY. MAKE SURE THEY ARE REINSTALLED IN THE ORIGINAL POSITIONS.
4.
INSERT SCREWS THROUGH THE MOUNTING TABS ON THE SPEAKER, SPEAKER RING, AND GRILL.
NOTE: IF INSTALLING HAWG WIRED SPEAKER GRILLS, REPLACE FACTORY GRILLS NOW.
5.
INSTALL THE NEW SPEAKERS, SPEAKER RINGS, AND GRILLS ON YOUR MOTORCYCLE.
6.
RE-CONNECT SPEAKERS TO YOUR FACTORY SPEAKER WIRING USING THE CHART BELOW.
NOTE: MAKE SURE THAT YOUR POLARITY IS CORRECT (+/- MATCHES ON ALL SPEAKERS).
7.
PERFORM A FINAL SYSTEM TEST. TURN THE KEY TO THE ACCESSORY POSITION AND VERIFY THAT
ALL COMPONENTS FUNCTION PROPERLY.
8.
INSTALL THE FAIRING COVER.
TIP: REFER TO MANUFACTURER INSTRUCTIONS IF NECESSARY.
RX50X-50 SPEAKER WIRES
CONNECT
TOGETHER
H-D® SOURCE UNIT MODELS
2 CHANNEL – USE FRONT ONLY
4 CHANNEL – USE BOTH
1998-2005
8 OHM
2006-20XX
2 OHM
1998-20XX
CVO
FRONT LEFT +
RED
f
f
e
e
WHT/ORG WHT/ORG WHT/ORG
FRONT LEFT –
BLK
f
f
e
e
L.GRN/WHT L.GRN/WHT L.GRN/WHT
FRONT RIGHT +
RED
f
f
e
e
GRY/RED GRY/RED GRY/RED
FRONT RIGHT –
BLK
f
f
e
e
L.GRN/BLK L.GRN/BLK L.GRN/BLK
REAR LEFT +
RED
f
f
e
e
BRN BRN BRN
REAR LEFT –
BLK
f
f
e
e
WHT/BRN WHT/BRN WHT/BRN
REAR RIGHT +
RED
f
f
e
e
GRN GRN GRN
REAR RIGHT –
BLK
f
f
e
e
L.GRN/BRN L.GRN/BRN L.GRN/BRN
