17
The required torque can be preselected in 20 settings with
the torque preselection ring (3). With the correct setting, the
insert bit is stopped as soon as the screw is screwed flush
into the material or when the set torque is reached.
Select a higher setting when driving out screws, or set to
the symbol “Drilling”.
The safety clutch is deactivated in the “Drilling” position.
The 3 LEDs of the battery charge-control indicator (9) flash
rapidly when the battery temperature is not within the
operating temperature range of -10º to +70
O
C (14ºF to
158ºF).
Setting the Torque
Gear Selection, Mechanical
Adjusting the Speed
Fully automatic spindle locking(Auto-lock)
Run-on Brake
Battery charge-control Indication
Gear 1:
Actuate the gear selector (4) only when the tool is
at a standstill.
Two speed ranges can be used with the gear selector (4).
Temperature Dependent Overload Protection
When used as directed, the power tool cannot be subject
to overload. When the load is too high or the allowable
battery temperature of 70
O
C (158ºF) is exceeded, the
electronic control switches off the power tool until the
temperature is in the optimum temperature range again.
The 3 LEDs of the battery charge-control indicator (9)
flash rapidly when the battery temperature is not within
the operting temperature range of -10 to +70
O
C (14ºF to
158ºF) and/or when the overload protection has actuated.
Protection Against Deep Discharging
Operating Instructions
The Li-ion battery is protected against deep discharging
by the “Electronic Cell Protection (ECP)”. When the battery
is empty, the tool is switched off by a protective circuit:
the inserted bit no longer rotates.
Apply the power tool to the screw only when it is switched
off. Rotating tool inserts can slip off.
Soft Grip
The gripping surface (soft grip) (5) reduces the danger of
slipping and thereby improves the grip and handling of
the tool.
At the same time, the rubber coating provides a
vibration-reducing effect for increased comfort for the
operator.
Tips
Cleaning and Maintenance
After longer periods of working at low speed, allow the
drill to cool down by running it for approx. 3 minutes at
maximum speed with no load.
For drilling in metal, use only perfectly sharpened HSS
(high-speed steel) drill bits.
Before screwing larger, longer screws into hard materials,
it is advisable to predrill a pilot hole with the core diameter
of the thread to approx. 2/3 of the screw length.
Place the direction of rotation direction switch (7) into the
middle position before carrying out any tasks on the tool,
e.g. changing bits or maintenance, or before transporting
or storing the tool. Accidental operation of the On/Off
switch (8) may result in injury.
Always pull the battery charger (12) out of the mains
socket and remove the battery pack before you clean or
maintain the device.
The cordless drill/driver is maintenance-free.
1) Always keep the tool clean, dry and free of oil or
grease.
Low speed range (0-400 RPM); for screwdriving or
working with a large drilling diameter.
Gear 2:
High speed range (0-1300 RPM); for working with a small
drilling diameter. If the gear selector (4) cannot be fully
engaged, lightly rotate the driver spindle with the drill bit
by twisting the drill chuck.
The speed of the switched on power tool can be variably
adjusted, depending on how far the On/Off switch (8) is
pressed.
Light pressure on the On/Off switch (8) results in a low
rotational speed. Further pressure on the switch results
in an increase in speed.
When the On/Off switch (8) is not pressed, the drill spindle
and thus the tool holder are locked.
This enables screws to be screwed in, even when the
battery is empty and allows for the tool to be used as a
screwdriver.
When the On/Off switch (8) is released, the chuck brakes
to a stop, thus preventing the run-on of the tool.
When driving in screws, wait until the screw is screwed in
flush with the material and then release the On/Off switch
8. By doing so, the head of the screw does not penetrate
into the material.
The battery charge-control indicator (9) consists of three
green LEDs, and indicates the charge condition of the
battery for a few seconds when the On/Off switch (8) is
pressed halfway or fully.
LED
Continuous lighting 3 x green
Continuous lighting 2 x green
Continuous lighting 1 x green
Slow flashing 1 x green
Capacity
≥66%
34-66%
11-33%
≤11%
CAUTION!
!
Summary of Contents for 5959003
Page 2: ...2 ...
