manualshive.com logo in svg

Hatteland JH 10T06 MMD, User Manual

Share
Download
Hatteland JH 10T06 MMD User Manual Download Page 73

7

Serial Communication (SCOM) Interface

Communication Interface

IND100084-1

INB100005-1 (Rev 19)

Communication settings #1 (before Jan 2005)

The communication options are set by switches, placed at the backside of the display. For most 

displays, these switches are labelled like seen on the illustration below. For adjustments, a thin 

object is required for reaching the switches. Some displays do not have this label or the dedicated 

holes. To change the settings, these switches can either be reached through the ventilation holes or 

the back cover must be demounted.

NOTE: The placement of the switches may vary from product to product!

By factory default the comport is set to RS232 mode, unless customer specified.

Communication mode

Duplex

Straight/Reverse

Rx/Tx for RS422, COM1

Address

[ Note: JHSCOM placement for products released and introduced BEFORE Jan 2005]

Summary of Contents for JH 10T06 MMD





















































































Reviews:

No comments

Brands by name

Popular brands

Load more brands