Hatteland JH 10T06 MMD User Manual Download Page 38

8

INB100005-1 (Rev 19)

IND100129-49

Specifications - JH 17T02 MMD (DVI)

A P P R O V A L S    &   C E R T I F I C A T E S

Power Specifications:

User Controls:

Synchronisation:

TFT Characteristics:

TFT Technology:

Physical Dimensions:

Supported Signal Inputs:

• 17.0 inch viewable image size

• a-Si TFT (Thin Film Transistor) Active Matrix

• SPVA (Super Patterned Vertical Alignment) mode

• Pixel Number       :  1280 x 1024

• Pixel Pitch (RGB)    :  0.264 (H) x 0.264 (V) mm

• Response Time      :  15 ms (typical), “black” to “white”

• Contrast Ratio        :  1000:1 (typical)

• Light Intensity       :  280 cd/m2 (typical)

• Viewable Angle      :  +/- 89 deg. (typical) (Up/Down/Left/Right)

• Active Display Area :

  

337.92 (H) x 270.336 (V) mm

• Max Colors 

     :  16.7 millions (depending on graphics card)

Power Supply Options:

• 115 & 230VAC - 50 / 60Hz 

: Model JH 17T02 MMD A1

• 24 VDC 

      

 

: Model JH 17T02 MMD A2

Power Consumption:

• Operating 

      

 

: 60 W (max)

Input Signal Terminal:

Sync Signal:

• Digital separate synchronisation

• Composite synchronisation

• Synchronisation on green. 

• Auto detects VGA -> SXGA, interlaced and non interlaced

• Video Signal 

     :  Analog RGB 0,7Vp-p

 

     :  Input Impedance 75 Ohm

Synchronisation Range:

• Horizontal 

     :  31,5 kHz to 91,1 kHz  

• Vertical 

     :  60 Hz* to 85 Hz

* Recommended for optimum picture quality

On front bezel:

• Power On/Off (push button)

• Brightness Control

• 2 x hotkeys

• Mode Status LED

Behind hatch:

• On Screen Display control (OSD/OSM)

Resolutions:

• VGA 

     :  640 x 480 (including 640 x 350)

• SVGA 

     :  800 x 600 (including 720 x 400)

• XGA 

     : 1024 x 768

• SXGA 

     : 1280 x 1024 *

Video Signals:

• Interlaced NTSC and PAL/SECAM video

• Composite video

• S-Video

* Recommended for optimum picture quality

This product have been tested / type approved by the following classification societies: (1=AC Ver & 2=DC Ver)

EN60945 4th 

(IEC945 4th)   

            

ABS

 - American Bureau of Shipping (1,2)

    GL

 - Germanischer Lloyd (1,2)

EN60529

 (IP66) (Applies only for flush mounting)  

BV

 - Bureau Veritas (1,2) 

 

     

LRS

 - Lloyd's Register of Shipping (1,2)

ClassNK

 - Nippon Kaiji Kyokai (1,2) 

 

          

DNV

 - Det Norske Veritas (1,2) 

     

RS

 - Russian Maritime Register of Shipping (1,2)

• 460 (W), 400 (H), 57 (D) mm

• Weight: 9.2 kg (approx w/bracket)

Environmental Considerations:

• Operating 

     : Temperature -15 deg. C to +55 deg. C  

   

 

       Humidity 30% to 90% (non condensing)

• Storage 

     : Temperature -20 deg. C to +60 deg. C

   

 

       Humidity 10% to 90% (non condensing)

• JH MMD BR  

= Bracket *

• JH MMDRO  

= Rotary Bracket *

• JH 17TSV 

= Sun Visor *

• JH VESA 17T01 = Vesa Bracket *

• JH VBUF 

= Video Buffer  

(1)

• JH SCOM 

= Remote Control

• JH XPR  

= External Power Relay

• Touch Screen   = Factory mounted

*Option: Standard or custom logo and color

*Option: See separate datasheet for specifications on bracket options.

(1)

 The JHVBUF is tested at resolutions up to 1600 x 1200. Both separate sync and 

composite sync is supported. The VGA output signal is at same resolution and sync as 

the input. The output is working even if the main display is turned off. (Power supply 

must be connected though)

Available Options:

• DVI-D (PC) signal  :  DVI-D Input 24pin Connector

• RGB (PC) signal     :  15pin mini D-SUB (female - Input)

• Composite Video    :  RCA Phono plug

• S-Video signal       :  S-Video (SVHS) plug

• AC Power signal     :  Std IEC Inlet Model JH 17T02 MMD A1

• DC Power signal     :  Screw terminal Model JH 17T02 MMD A2

Accessories:

• Touchscreen 

     :  1 x D-SUB 9P Connector (female)

• Remote Control      :  2 x D-SUB 9P Connectors (female)

Safety Considerations:

Even although the test conditions for bridge units provide for a maximum

operating temperature of 55°C, continuous operation of all electronic

components should, if possible, take place at ambient temperatures of only

25°C. This is a necessary prerequisite for long life and low service costs.

Compass Safe Distance:  JH 17T02 MMD 

Standard: 90cm 

      Steering: 70cm

T E C H N I C A L   D E S C R I P T I O N

M E C H A N I C A L   D E S C R I P T I O N

Note: All specifications are subject to change without prior notice!

Summary of Contents for JH 10T06 MMD





















































































Reviews: