HASE 8160 Owner'S Manual Download Page 7

HearthStone Quality Home Heating Products, Inc.                                                                    

   

Luno Model #8160 

O

WNER

I

NFORMATION

 

The installation must conform with local codes or, in 
the absences of local codes, the current National Fuel 
Gas Code, ANSI Z223.1 (NFPA 54) or CAN/CGA 
B149 Installation Code.  

(Installer l’appareil selon les 

codes ou règlements locaux, ou, en l’absence de tels 
règlements, selon les Codes d’installation CAN/CGA-
B149.)

 

Contact your dealer for any necessary warranty 
service. 

This stove is warranted by: 

Hearthstone

 

Quality Home Heating Products, 

Inc

® 

317 Stafford Ave. 
Morrisville, Vermont  05661 

 

D

AILY 

O

PERATION

 

The Luno is easily operated by the homeowner once 
it is installed and adjusted by qualified service 
personnel. The unit can be controlled automatically 
via the programmable remote control, or manually by 
placing the Remote Control Receiver switch in the 
‘ON’ position during the heating season. When using 
the remote T-stat transmitter (switch in the ‘REMOTE’ 
position), set it to the desired room temperature and 
the unit will cycle on and off as required. If you select 
the ‘ON’ position the unit will run (burn) regardless of 
room temperature. You can vary the rate of heat 
output by adjusting the variable output control located 
on the gas control valve to meet the heating 
requirements of the season. Choosing a low flame 
setting will result in longer burn cycles at a reduced 
output, while choosing a high flame setting will result 
in a shorter, hotter burn cycle. Through trial and error, 
the homeowner can select the optimum flame size for 
their setting and application. 

During the summer non-heating season, switch the 
remote receiver to “OFF”, and turn off the pilot. This 
will improve the overall efficiency of the unit as the 
fuel used by the pilot is wasted. When putting the unit 
back into service, follow the lighting instructions 
described on page 16. 

When the unit is first lit, especially when cool, it is 
normal to experience some condensation on the 
inside of the window glass. This condensation will 
evaporate within the first few minutes of operation. If 
you note continuous condensation on the window 
glass or dripping water from any part of the unit or 
venting system (chimney), immediately discontinue 

operation of the unit and contact qualified service 
personnel. 

Clean the area around, under, and behind the unit on 
a regular basis to prevent the accumulation of dust 
and lint. 

The Luno requires minimal routine maintenance and 
care.  Ensure the Luno is cool and off while cleaning, 
or servicing.  Have qualified service personnel 
inspect the unit, and venting system once a year to 
insure that they are clean, free of obstructions, safe, 
and in good working order.  If service or maintenance 
is required, ensure qualified service personnel 
perform it. 

S

ERVICE 

C

AUTION

 

If you believe your Luno is in any way, not performing 
properly, immediately discontinue operation until the 
unit is inspected and approved by qualified service 
personnel.  Prior to servicing the unit, turn the valve 
control knob clockwise to “OFF”. The unit should be 
cool prior to servicing and cleaning. Use of any 
components not supplied by Hearthstone on the 
stove voids all warranties. 

Do not substitute 

components. 

 

CAUTION: REPLACE ANY SHIELD, DOOR, OR 
SAFETY SCREEN COMPONENT REMOVED FOR 
SERVICING, PRIOR TO OPERATING THE UNIT. 

 

WARNING: FAILURE TO POSITION THE PARTS IN 
ACCORDANCE WITH THESE DIAGRAMS OR 
FAILURE TO USE ONLY THE PARTS 
SPECIFICALLY APPROVED WITH THIS 
APPLIANCE MAY RESULT IN PROPERTY DAMAGE 
OR PERSONAL INJURY. 

Conditionally approved for purchased mobile home 
installation. This appliance may be installed in an 
aftermarket permanently located, manufactured (mobile) 
home, where permitted by local codes. 

This appliance is only for use with the types of gas 
indicated on the rating plate (NG and LP). This appliance is 
factory set to burn Natural Gas (NG), but is easily 
converted for use with Liquid Propane (LP) with the 
included conversion kit. Only a qualified service technician 
should convert this stove.  

Cet appareil peut être installé dans un maison préfabriquée 
(mobile) déjà installée à demeure si les règlements locaux 
le permettent. 

Cet appareil doit être utilisé uniquement avec les types de 
gas indiqués sur la plaque signalétique. Ne pas l’utiliser 
avec d’autres gas sauf si un kitde conversion certifié est 
installé

 

 

 

4

Summary of Contents for 8160
































Reviews: