manualshive.com logo in svg

Hart Sceintific DewK 1620, User Manual

Share
Download
Hart Sceintific DewK 1620 User Manual Download Page 68

Graphs include time tick marks that occur at hourly intervals for time scales 24
hours or less or at daily intervals for time scales greater than 1 day. Time tick
marks are labeled at intervals with the hour or day, labels being placed below
and to the right of tick marks. Tick marks with labels are drawn with short con-
tinuous lines, and tick marks without labels are drawn with dotted lines.

7.4

Alarm Menu

The ALARM menu allows the setting and viewing of alarms. The functions
that appear in this menu are ALARM SETTING, SENSOR ALARM, SYSTEM
ALARM, and ALARM VIEW. Alarm settings may be password protected (see
Section 7.5.4, Password).

The

ud

buttons are used to select the menu option. The

lr

buttons are

used to change the parameter setting. Press the

Enter

button to save the new

setting. Press the

Exit

button to cancel any changes made and exit to the menu.

7.4.1

Alarm Setting

The ALARM SETTING function is used to enable or disable visible and audi-
ble alarm notifications. The parameters are BEEP and DISPLAY.

When the BEEP parameter is ON, the thermo-hygrometer emits an audible
beep during an alarm condition. For the power alarm it is four short beeps ev-
ery 20 seconds. For the battery alarm it is three short beeps every minute.

For the sensor disconnect alarm it is two short beeps every measurement pe-
riod. For measurement alarms it is one long beep every measurement period.

60

Hart Scientific

7 Menu Functions

Figure 37

Alarm

Summary of Contents for DewK 1620































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands