Harris ACO6800+ASID Installation And Operation Manual Download Page 125

Page: 125 / 136

ACO6800

Installation and Operation Manual

111

Appendix A

Communication and Control

Troubleshooting Tips

Software Communication Problems

The frame is powered up, but the module does not communicate
with CCS Navigator.

Solutions

•

Ensure you have specified the proper module slot.

See the installation and operation manual for your frame for more
information about slot identification.

•

Verify whether there is an ICE6800

or 6800

ETH module installed in the

frame.

•

Remove any legacy 6800 series product that is in the frame.

CCS software cannot communicate with legacy 6800 series products, even
though these modules may operate with card-edge controls in an FR6802

frame. Legacy 6800 products do not have the “

” symbol on their extractor

handles.

•

Check for bent pins on the back module by following this procedure:

Unplug the front module.

b. Unscrew and remove the back module.

Inspect the 20- or 30-pin spring connector at the bottom of the back
module (

Figure A-1 on page 112

), and verify that the connector does

not have any slightly bent or pressed pins.

d. Carefully reposition any bent pins; If this is not possible, contact

Customer Support.

Summary of Contents for ACO6800+ASID


































































































































Search results

Summary of Contents for ACO6800+ASID

Reviews:

Harris ACO6800+ASID, Installation And Operation Manual, Page: 125 / 136

Search results

Summary of Contents for ACO6800+ASID

Reviews: