Harmar Mobility AL003 Installation & Service Manual Download Page 4 | Manualshive

Page: 4 / 36

Harmar Mobility AL003 Installation & Service Manual Download Page 4

Outside Vehicle Lifts:

Installation & Service Manual

06DEC19 | P/N: 630-00106 REV A

4

OUTSIDE VEHICLE LIFTS:

SECTION 1

INTRODUCTION

Section 1

Introduction

DEVICE NAME: HARMAR

OUTSIDE VEHICLE LIFTS

Indications of Use: The intended use of the Outside
Vehicle Lift is to lift, secure and transport an
unoccupied mobility device for patients or mobility-
impaired persons.

READ AND UNDERSTAND

Read and understand this manual prior to installation
or operation. Having an overall understanding of the
lift and proper installation techniques will help you
save time, energy and avoid possible injury.

This manual provides instructions for proper
installation of Outside Vehicle Lifts. Please refer to
the Owner’s Manual for operating instructions. Be
sure to provide the Owner’s Manual to the owner of
the lift before it is put into service. Any alterations to
the equipment without written authorization by the
manufacturer may void the warranty.

«
...
2
3
4
5
6
...
»

Summary of Contents for AL003





































Reviews:

No comments