Harmar Mobility AL003 Page 3 Installation & Service Manual Download | Manualshive

Page: 3 / 36

background image

OUTSIDE VEHICLE LIFTS

TABLE OF CONTENTS

Outside Vehicle Lifts:

Installation & Service Manual

06DEC19 | P/N: 630-00106 REV A

3

Table of Contents

INTRODUCTION ...............................................4

Device Name: Harmar Outside Vehicle Lifts .............4
Read and Understand .....................................................4

SAFETY .................................................................5

Safety Definitions ............................................................5
Required Practices ...........................................................5

PREPARATION ...................................................6

Recommended Tools  ......................................................6
Required Tools  .................................................................6
Unpacking the Lift  ...........................................................6
Recommended Torque Table ..........................................6
Checking the Box Contents ...........................................7
Vehicle Hitch  ....................................................................8
Hitch Adapters  .................................................................9
Hitch Adapter Size Chart  ............................................ 10

INSTALLATION ................................................ 12

Wiring the Vehicle ........................................................ 12
Hitch Adapter Installation ........................................... 15
Swing-Away or Hitch Post Installation .................... 16
AL030 Power Tote Installation with
Ball Mount Hitch Adapter ........................................... 17

CHAIR PREPARATION ................................... 19

Anchor Plate .................................................................. 19
U-Bolt Hardware Kit .................................................... 20

LIFT ADJUSTMENTS .................................... 21

Hold-Down Foot Height Setting  ..............................  21
AL100, AL160 & AL300 Wheel
Cradle Adjustments  ....................................................  22
AL560 & AL560XL Platform Adjustments  .............  23
AL560 & AL580 - Hold-Down

arm Adjustments .......................................................... 24
AL580-HDX .................................................................. 25

TROUBLESHOOTING ................................... 29

Troubleshooting Table ................................................ 30
Manual Override ......................................................... 31

MOTOR COVER WIRING SCHEMATIC ... 32

«
1
2
3
4
5
...
»

Summary of Contents for AL003





































Reviews:

No comments

Related manuals for AL003

Brand: ZKTeco Pages: 18

Brand: ICP DAS USA Pages: 5

Brand: ICP DAS USA Pages: 7

Brand: Measurement Computing Pages: 32

Brand: BRAVILOR BONAMAT Pages: 76

Brand: Simplex Pages: 40

Gator Grip Drum EGG-1

Brand: Wesco Pages: 2

Brand: Welding Industries Malaysia Pages: 20

Brand: CEA Pages: 92

RhinoBond RBHW1

Brand: OMG Pages: 8

Brand: First Power Pages: 16

Brand: M-system Pages: 4

RAZOR CUT 45 PFC

Brand: Xcel-Arc Pages: 24

Brand: Redback Pages: 16

Brand: F.F. Group Pages: 82

VIPER CUT 30Mk II

Brand: Xcel-Arc Pages: 24

Brand: Maxon Pages: 3

Brand: Braun Pages: 41

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands