background image

3-90-00885R17_02/15

Model(s):

XXV Freestanding Pellet Stove

INSTALLER:  Leave this manual with party responsible for use and operation.

OwNER:  Retain this manual for future reference.

Contact your local dealer with questions on installation, operation or service.

NOTICE: SAVE THESE INSTRUCTIONS

Please read this entire manual before 

installation and use of this pellet fuel-

burning room heater.  

Failure to follow these instructions could 

result in property damage, bodily injury 

or even death.

•  Do not store or use gasoline or other flammable vapors 

and liquids in the vicinity of this or any other appliance.

•  Do not overfire - If any external part starts to glow, you 

are overfiring. Reduce feed rate.  Overfiring will void 

your warranty.

•  Comply with all minimum clearances to combustibles 

as specified. Failure to comply may cause house fire.

Check building codes prior to installation.

•  Installation MUST comply with local, regional, state and 

national codes and regulations.

•  Contact local building or fire officials about restrictions 

and installation inspection requirements in your area.

Tested and approved for wood pellets and shelled field 

corn fuel only.  Burning of any other type of fuel voids 

your warranty.

Hot glass will cause burns.

•  Do not touch glass until it is cooled
•  NEVER allow children to touch glass
•  Keep children away
•  CAREFULLY SUPERVISE children in same room as 

stove.

•  Alert children and adults to hazards of high temperatures.

  High temperatures may ignite clothing or other 

flammable materials.

•  Keep clothing, furniture, draperies and other flammable 

materials away.

HOT SURFACES!

Glass and other surfaces are hot 

during operation AND cool down.

To  obtain  a  French  translation  of  this  manual,  please 

contact your dealer or visit www.harmanstoves.com

Pour obtenir une traduction française de ce manuel, s’il 

vous  plaît  contacter  votre  revendeur  ou  visitez  www.

harmanstoves.com

NOTE

 wARNING

 wARNING

Installation & Operation Manual

Care and Operation

caution

!

caution

!

Summary of Contents for XXV Freestanding Pellet Stove





































Reviews: