QUICK START GUIDE
HPX-AV102-USB-R
USB 3.0 Module with Retractable
MyTurn
TM
Ready Cable
Overview
The HydraPort
®
Retractable Cable Module is designed to be used in conjunction with
the HPX-600/900/1200/1800 or the Hydraport Touch (7”/10”) Connection Port base
assembly, to provide the convenience of various types of cables in a HydraPort System.
The
HPX-AV102-USB-R
USB 3.0 Module with Retractable Cable (FG552-37) provides a
USB 3.0 cable in a retractable spool that mounts into the HydraPort base assembly
(FIG. 1). USB 3.0 cable features transmission speeds of up to 5 Gbit/s and supports
charging devices via 4.5W: 5V@900mA charging current.
With the MyTurn™ Source Selection Button (FG554-21) optional accessory,
participants can send their content to a display at the press of a button without moving
from their seat. Any
MyTurn-Ready
cable may be equipped with the MyTurn solution.
See “Optional MyTurn™ Source Selector Button” on page 2.
Installation
Warning! - Do not attempt to open the retractable cable module enclosure. There are
no serviceable parts inside the module.
- Opening the module enclosure may result in an uncontrolled release of spring
forces which could cause serious injury and/or equipment damage.
- Opening the module enclosure will void the product warranty.
Warning! - installation of the Hydraport in the table should ensure the pull-out length
of the cable can reach all potential users of connectivity, as excessively pulling on a
fully extended cable can irreparably damage the retractor module.
Caution: Only use a hand-held #2 Phillips-head screwdriver for mounting this unit. Over-
tightening the screws can hinder performance or damage the unit.
For existing HPX installations, the HPX base must be removed from the mounting
surface. See “Existing Installations” on page 2. for HPX Base removal instructions.
1.
Remove the (silver) pivot screw in the center of the End Cap (FIG. 2). There is an
internal tooth washer underneath it. Keep them together for re-installation.
2.
Remove the four (black) sheet metal screws that secure the two-piece End Cap to
the HPX assembly (additional top two screws only on one-piece end cap models).
3.
Gently slide the End Cap out of the HPX base assembly.
The HPX-AV102-USB-R RCM cable cartridge mounts from underneath the table to
simplify installation and upgrade of retractable cable modules. This version RCM has a
detachable mounting collar that is installed into the Hydraport base first and then the
cable cartridge is reattached to the mounting collar
Securely holding the HPX-AV102-ETH-R RCM, extract enough cable to lay the cable
cartridge on the floor while installing the mounting collar into the HPX Base Assembly
(~3ft). When extracting 5 foot (1.5m) cable from the RCM, follow these simple steps:
4.
Pull up to 1.5 meters of cable straight up out of the RCM and then lay it down.
5.
Watch for a red tape on the cable when extracting. It is a warning to slow pull for
the final 1 foot to avoid damage to the RCM (FIG. 3).
6.
Pull the cable cartridge trigger (FIG. 4) to release the mounting collar tongue.
7.
Lift the mounting collar away from the cable cartridge until the tongue is clear and
then slide to the side to clear the hook.
8.
Feed the mounting collar up through the table cutout to reach the HPX base
assembly. Align the mounting notches on the mounting collar with the mounting
rails on the HPX (FIG. 4).
Note:
Module mounting collars are notched in a “tongue and groove" type fashion
to ensure that all modules are oriented correctly in the HPX. Note the orientation of
the notched mounting collar on each module before sliding the module(s) into the
HPX assembly.
9.
Slide the mounting collar into position.
10. Install any remaining module mounting collars into the HPX base.
Re-Install the End-Cap
Caution: Do not use a high-powered torque screw driver. Over-tightening these screws
can damage the product.
1.
Align the mounting notches on the end cap with the mounting rails on the HPX base.
2.
Slide the End Cap into the HPX base until it is fully inserted against the end of the
base assembly. Watch out for the tension spring under the pivot pawl popping the
pivot pawl off the end cap while pressing against the lid pivot point.
3.
Secure the End Cap with the 4 to 6 (black) sheet metal screws (FIG. 2).
4.
Replace the (silver) pivot screw in the center of the End Cap.
FIG. 1
HPX-AV102-USB-R USB 3.0 MODULE WITH RETRACTABLE CABLE
FIG. 2
HPX BASE ASSEMBLY - MOUNTING/PIVOT SCREW LOCATIONS
Retractable 5 foot (1.5 meter) USB MyTurn Ready cable
connects to Source device
Cable Retract Push Button
Mounting notches (both sides)
5 foot Cable Pigtail (1.5 meter)
Pull trigger to initiate
separation of the mounting
collar from cartridge
Slide-hook and catch secures
mounting collar to cartridge
has a Male Type A connection,
or use the included adapters to
convert to Female Type A or Male Type B
Remove Pivot Pawl
and Pivot Screw
Remove four remaining
sheet metal screws
(highlighted)
Remove top two screws
(only on one-piece end
cap models)
FIG. 3
EXTRACTING CABLE - WARNING BAND
FIG. 4
HPX-AV102-USB-R MOUNTING COLLAR REMOVAL
FIG. 5
RETRACTABLE CABLE MODULE - MOUNTING INTO AN HPX BASE ASSEMBLY
Warning Tape
4 Feet
1 Foot
Slow Pull
Pull
Trigger
Detachable
Mounting
cable cartridge
Collar
DO NOT
twist the
detached cable
cartridge. If a twist
exists in the cable
when remounted the
Mounting
tongue
retractor will not
fully retract..
Slide the mounting
notches on both sides
of the mounting collar onto
the mounting rails on both
sides of the HPX Base
HPX Base Top Surface
Table cutout
Mounting
Collar
Retract Button