background image

REAR PANEL CONNECTIONS  

5

Rear Panel Connections

Line-Level Subwoofer (SUB) Input:

Con-

nect the subwoofer output of a receiver with
digital surround sound decoding, such as Dolby*
Digital or DTS

®

, to this input. This input bypasses

the SUB-TS7’s internal crossover circuitry, and
should only be used with a filtered signal. If your
receiver does not have digital decoding, you
should use the 

Line-Level Full-Range Inputs

instead.

Line-Level Full-Range Inputs:

Connect

the line-level subwoofer output or preamp out-
put(s) of your receiver or amplifier to these
inputs. If your receiver does not have a separate
subwoofer output, use a Y-adapter (not supplied)
to bridge the receiver’s preamp output to the
main amp input for that channel, and connect
the long end of the adapter to the correspon-
ding line-level input on the SUB-TS7. If your
receiver has only a single subwoofer output, you
may connect it to either the left or right line-
level input on the SUB-TS7, and no Y-adapter is
needed.

Speaker-Level Outputs:

If you are using

the 

Speaker-Level Inputs

on the SUB-TS7,

you should connect these binding-post terminals
to your front left and right speakers, remember-
ing to maintain polarity by connecting the (+)
terminal on the SUB-TS7 subwoofer to the (+)
terminal on the speaker, and the (–) terminal on
the SUB-TS7 subwoofer to the (–) terminal on
the speaker. If you are not using the 

Speaker-

Level Inputs

, then connect your front left

and right speakers directly to your receiver or
amplifier. See pages 9 through 12 for further
information on speaker connections.

Speaker-Level Inputs:

Connect these

binding-post terminals to the main left and right
speaker terminals of your receiver or amplifier, if
your receiver or amplifier does not have a line-
level subwoofer output. Remember to maintain
polarity by connecting the (+) terminal on the
receiver/amplifier to the (+) terminal on the
SUB-TS7 subwoofer, and the (–) terminal on the
receiver/amplifier to the (–) terminal on the SUB-
TS7 subwoofer.

Master Power Switch:

Place this switch in

the “•” position to power-on the SUB-TS7 sub-
woofer. The SUB-TS7 will then be either in the
Standby mode or completely on, depending on
the position of the 

Music-Sense On/Off

Switch

.

AC Power Cord:

Make sure to plug this 

cord into an active, unswitched electrical outlet
for proper operation of the SUB-TS7.
The cord should not be plugged into the
accessory outlets found on some audio
components.

Summary of Contents for HKTS 7

















Reviews: