I N S T R U C T I O N S
27 mm Midrange Endstops and End Controls (Sold as a Pair)
E2700, E2730, E2750, E2756
Fits R27 and Midrange CB Track
Strictly follow all instructions to avoid an accident, damage to your vessel, personal injury
or death. See www.harken.com/manuals for additional safety information.
USA – Tel: (+1) 262-691-3320 • Web: www.harken.com • Email: [email protected]
Italy – Tel: (+39) 031.3523511 • Web: www.harken.it • Email: [email protected]
IMPORTANT: See Inspection and Maintenance at end of manual.
See www.harken.com/manuals for more instructions
Mounting to Track
Note: E27 end controls do not fit older non-CB track.
The E27 end controls’ interior ridges that extend into the
waist of the track are too deep to fit non-CB track. E27 end
controls require deep grooves for wire keepers on CB cars.
E27 end controls
require deep grooves
for wire keepers on
CB cars
R27 low-beam track has holes drilled for end controls
and enstops if entire length is used. If you shorten one
end, make cut so end control screw passes through a
track fastening hole. It is best to have track cut with an
electric cross cut saw at a machine shop. Low beam
track may be cut using a hacksaw but it is difficult to get
a straight, even cut. Measure from center of hole to end
of track so center is
9
/
16
" (14 mm) from track end. If this
does not work, make sure that end control screw hole
does not interfere with mounting or pinstop hole.
Note: Since trim caps are not used with E27 or
E32 end controls, do not leave room for them.
R32
End Control
Hole
Track Mounting Hole
9
/
16
" (14 mm)
Specifications
19
/
32
" (15 mm)
Part
No.
Max line
Ø
Maximum
working load
Breaking
load
Purchase
Part
No.
Max line
Ø
Maximum
working load
Breaking
load
Purchase
in
mm
lb
kg
lb
kg
in
mm
lb
kg
lb
kg
E2730
3
/
8
10
1800
816
3600 1633 1:1, 2:1 E2756
3
/
8
10
600
272
1500
680
3:1, 4:1
E2750
3
/
8
10
1800
816
3600 1633 3:1, 4:1
Fasteners — Not Included
1
1
/
8
28 mm
2
1
/
8
55 mm
Fasteners (One Set for Each Control):
1 (one)
5
/
16
" (8 mm) flathead A4 (316) or A2 (18-8)
stainless steel mounting screw.
End control and track thickness is shown at right.
When purchasing fasteners, add deck thickness and
enough threads to extend below washer and nut.
1 (one) washer
1 (one) locknut for each end control.
Drill Bit:
11
/
32
" (8.5 mm)
E2700 Endstop
Subtract 1/8" (2.5mm) from
numbers above to determine
screw length.
Drill Size
11
/
32
" (8.5 mm)
I N S T R U C T I O N S
27 mm Midrange Endstops and End Controls (Sold as a Pair)
E2700, E2730, E2750, E2756
Fits R27 and Midrange CB Track
Strictly follow all instructions to avoid an accident, damage to your vessel, personal injury
or death. See www.harken.com/manuals for additional safety information.
USA – Tel: (+1) 262-691-3320 • Web: www.harken.com • Email: [email protected]
Italy – Tel: (+39) 031.3523511 • Web: www.harken.it • Email: [email protected]
IMPORTANT: See Inspection and Maintenance at end of manual.
See www.harken.com/manuals for more instructions
Mounting to Track
Note: E27 end controls do not fit older non-CB track.
The E27 end controls’ interior ridges that extend into the
waist of the track are too deep to fit non-CB track. E27 end
controls require deep grooves for wire keepers on CB cars.
E27 end controls
require deep grooves
for wire keepers on
CB cars
R27 low-beam track has holes drilled for end controls
and enstops if entire length is used. If you shorten one
end, make cut so end control screw passes through a
track fastening hole. It is best to have track cut with an
electric cross cut saw at a machine shop. Low beam
track may be cut using a hacksaw but it is difficult to get
a straight, even cut. Measure from center of hole to end
of track so center is
9
/
16
" (14 mm) from track end. If this
does not work, make sure that end control screw hole
does not interfere with mounting or pinstop hole.
Note: Since trim caps are not used with E27 or
E32 end controls, do not leave room for them.
R32
End Control
Hole
Track Mounting Hole
9
/
16
" (14 mm)
Specifications
19
/
32
" (15 mm)
Part
No.
Max line
Ø
Maximum
working load
Breaking
load
Purchase
Part
No.
Max line
Ø
Maximum
working load
Breaking
load
Purchase
in
mm
lb
kg
lb
kg
in
mm
lb
kg
lb
kg
E2730
3
/
8
10
1800
816
3600 1633 1:1, 2:1 E2756
3
/
8
10
600
272
1500
680
3:1, 4:1
E2750
3
/
8
10
1800
816
3600 1633 3:1, 4:1
Fasteners — Not Included
1
1
/
8
28 mm
2
1
/
8
55 mm
Fasteners (One Set for Each Control):
1 (one)
5
/
16
" (8 mm) flathead A4 (316) or A2 (18-8)
stainless steel mounting screw.
End control and track thickness is shown at right.
When purchasing fasteners, add deck thickness and
enough threads to extend below washer and nut.
1 (one) washer
1 (one) locknut for each end control.
Drill Bit:
11
/
32
" (8.5 mm)
E2700 Endstop
Subtract 1/8" (2.5mm) from
numbers above to determine
screw length.
Drill Size
11
/
32
" (8.5 mm)
