Hardo OptiLine A1 Series Use And Maintenance Instruction Download Page 11

 

 
 

Strona 

11

 z 

16

 

 

 

Figure 4. Possible connection diagrams of OptiLine **-*******A1-  

 

After making connections, the earthing efficiency should be checked in accordance with local regulations and the 
luminaire should be closed again, i.e.: 
 

 

Set the top base (reflector) in the starting position; 

 

Tighten two non-loose screws with a screwdriver; 

 

Close the protective diffuser made of polycarbonate with clips. 

 

6. 

WORK IN EMERGENCY MODE 

6.1 General information 

 

During OptiLine **-*******A1- are powered by 230VAC,50Hz mains voltage, the process of charging the built-in Ni-Cd 
battery  packs  takes  place.  Loss  of  mains  voltage  causes  the  OptiLine**-*******A1-  luminaires  to  automatically  enter 
emergency  mode  when  powered  from  built-in  battery  packs.  The  emergency  working  time  under  rated  operating 
conditions shall not be less than 1.5 hours. The required battery charging time is min. 24 hours. 
 
In accordance with the requirements for emergency lighting, OptiLine luminaires**-*******A1- have implemented: 
 

 

Built-in automatic functional test execution. Functional tests last one minute and are performed:  
- first 

– 1 hour after the first start; 

- next 

– 7 days after the end of the previous one. 

The test result shall be indicated by LEDs in accordance with paragraph 6.3 

 

Built-in automatic capacitance testing. Capacitance tests check the operating time of the luminaire in emergency 
mode and are performed: 
- the first 

– up to 4 weeks after launch; 

- next 

– 52 weeks after the end of the previous one 

The test result shall be indicated by LEDs in accordance with paragraph 6.3 

 

Battery pack discharge control system to prevent deep discharge; 

 

Battery charging control system. After a full charge, the system goes into the so-called maintenance charge; 

 

LED module efficiency control system (short circuit, open circuit); 

 

Operating status indication system by means of an indicator diode in accordance with paragraph 6.3. 
 

6.2 Battery pack, commissioning 

 

 

 
DANGER: 

OPERATIONS SHOULD BE PERFORMED IN THE ABSENCE OF A POTENTIALLY 

EXPLOSIVE ATMOSPHERE. 
 

 

Summary of Contents for OptiLine A1 Series

















Reviews: