background image

Page 4

For technical questions, please call 1-800-444-3353.

SKU 66399 

        

SYMBOLS AND SPECIFIC 

SAFETY INSTRUCTIONS

Symbol Definitions

Symbol

Property or statement

n

o

No-load speed

.../min

Revolutions or reciprocation per 

minute

PSI

Pounds per square inch of pressure

ft-lb

Foot-pounds of torque

BPM

Blows per minute

CFM

Cubic Feet per Minute flow

SCFM

Cubic Feet per Minute flow at 

standard conditions

NPT

National pipe thread, tapered

NPS

National pipe thread, straight

WARNING marking concerning Risk 

of Eye Injury.  Wear ANSI-approved 

eye protection.
WARNING marking concerning Risk 

of Hearing Loss.  Wear hearing 

protection.
WARNING marking concerning Risk 

of Respiratory Injury.  Wear NIOSH-

approved dust mask/respirator.

WARNING marking concerning Risk 

of Explosion.

Specific Safety Instructions

1. 

THE METAL PARTS OF THE 

COMPRESSOR AND HOSES WILL 

BECOME HOT DURING USE.

2. 

Do not use cigarette lighter adaptor 

to power this unit.

  If powered with the 

battery of a vehicle, start and run engine 

during inflation period.

3.  The warnings and precautions discussed 

in this manual cannot cover all possible 

conditions and situations that may oc-

cur.  It must be understood by the opera-

tor that common sense and caution are 

factors which cannot be built into this 

product, but must be supplied by the 

operator.

4.  WARNING:  Some dust created by 

power sanding, sawing, grinding, drilling, 

and other construction activities, con-

tains chemicals known [to the State of 

California] to cause cancer, birth defects 

or other reproductive harm.  Some ex-

amples of these chemicals are: 

•  Lead from lead-based paints 

•  Crystalline silica from bricks and ce-

ment or other masonry products 

•  Arsenic and chromium from chemically 

treated lumber 

Your risk from these exposures varies, 

depending on how often you do this type 

of work.  To reduce your exposure to 

these chemicals: work in a well ventilat-

ed area, and work with approved safety 

equipment, such as those dust masks 

that are specially designed to filter out 

microscopic particles.  (California Health 

& Safety Code § 25249.5, 

et seq.

WARNING:  The brass components 

of this product contain lead, a chemi-

cal known to the State of California to 

cause birth defects (or other reproductive 

harm).  (California Health & Safety code 

§ 25249.5, 

et seq.

)

5.  Only use with accessories rated to 

handle the forces exerted by this tool 

during operation.  Other accessories not 

designed for the forces generated may 

break and forcefully launch pieces.

6.  Attach all accessories properly to the tool 

before connecting the air supply.  A loose 

accessory may detach or break during 

operation.

Summary of Contents for Central Pneumatic 66399













Reviews: