Specifications
Brand Name: Happymodel
Item Name:
Mobula7 HD 2-3S 75mm Brushless whoop drone
Wheelbase: 75mm
Size: 98mm*98mm*
mm
45
Weight:
72g(with Original 3s 300mah Lipo battery )
Flight controller connection diagram
Package includes:
Item Name
Mobula7 V3 Frame
Option1: Crazybee F4FR V3.0 PRO FC built-in Frsky NON-EU RX
Option2: Crazybee F4FS V3.0 PRO FC built-in Flysky RX
Option3: CrazybeeF4 PRO V3.0 with external DSM2/X receiver
Option4: Crazybee F4 V3.0 PRO FC no RX verion
EX1102 KV9000 Motor
40mm propeller(4cw+4ccw)
Caddx Turtle v2+1080p 60fps DVR
Whoop_vtx 5.8G 40ch 25mw-200mw VTX
3S 11.4v 300mah 30C/60C battery
Propeller disassemble tool
Screwdriver
Qty
1
1
4
1
1
1
1
1
1
Mobula7 HD brushless whoop Racing Drone PNP
version
Receiver configuration
Crazybee F4 PRO
R1(RX1
No inverter)
IR1(RX1
With inverter)
+5V
GND
TX1
TX2
RX2
XM/XM+ /FHSS/FD800 RX
SBUS
+5V
GND
Smart audio control
(VTX support)
Fli10/Flit14/Fli14
+
/SP09X RX
IBUS/DSM2/DSMX
+5V
GND
Smart audio control
(VTX support)
TBS Crossfire Nano
+5V
GND
Smart audio control
(VTX support)
RX
TX
1. Connect your Serial-based receiver to the Crazybee F4 PRO flight controller according to the
bellowing connection diagram table
2. Enable Serial RX for UART1
Sbus/IBUS/DSM2/DSMX receiver
or Serial RX for UART2(TBS
crossfire Nano receiver) , then choose the correct serial Receiver provider based on the
protocol of your receiver
SBUS signal connect to IR1 pad and enable Serial_RX for UART1
IBUS/DSM2/DSMX signal connect to R1 pad and enable Serial_RX for UART1
Arm/Disarm the Motor
Use frsky x9d as an example
1. The Default Arm/Disarm switch for Mobula7 HD is AUX1(Channel 5),and you can also customize it
with Betaflight Configurator.
3
.
The default channel map for Mobula7 HD PNP version is TAER1234, please make sure your
transmitter is matched, otherwise it will can't be armed. Toggle the AUX1 Switch ,the Green
LED on the flight controller will getting to be solid, this indicates the motor was armed . And
also you can found “Armed” displayed on your FPV Goggles or the FPV Monitor. Please make
sure keep the Mobula7 HD
level before arming .Be careful and enjoy your flight now !
2.Turn on the Frsky transmitter (Use X9D+ as an example) and move to the MIXER interface,
Set “SA” or “SB” switch etc. for Ch5 to ARM/DISARM the motor
.
Toggle the AUX1 Switch, the Green LED on
the Flight controller will getting to be solid
Toggle the AUX1 Switch, the Green LED on
the Flight controller will getting to be solid
TBS CRSF NANO connect CH1(TX) to RX2 and CH2(RX) TO TX2 (Make sure telemetry in the
configure is enable)
DSM2
DSMX
XM
/
XM
+/
FD800
SBUS
/
FHSS
Fli10
/
Flit10
/
Fli14
/
RX2A
PRO
/
FS82
TBS
CRSF
NANO
BUZ
+
+
5V
output
GND
Video
_
out
TX1
TX2
IRX1
