2. Turn on your Frsky Taranis transmitter, and move to BIND OPTION from SETUP MENU,
Choose receiver mode D16 or D8 according to your Betaflight receiver configuration
(Frsky_X = D16 mode, Frsky_D=D8 mode)we recommend use D8 mode
Features
AIO 4IN1 Crazybee F4 Lite flight controller built-in 5.8G VTX
Extreme light 1S 65mm Brushless whoop only 20g
Runcam Nano3 The lightest 1/3 CMOS 800TVL Camera
Smooth and powerful
Compatible for 1S Lipo/LIHV
Camera Angle adjustable
Flight controller connection diagram
Arm/Disarm the Motor
1. The Default Arm/Disarm switch for Mobula6 is AUX1(Channel 5),and you can also customize it
with Betaflight Configurator.
3
.
The default channel map for Mobula6 Frsky version is TAER1234, please make sure your
transmitter is matched, otherwise it will can't be armed. Toggle the AUX1 Switch ,the Green
LED on the flight controller will getting to be solid, this indicates the motor was armed . And
also you can found “Armed” displayed on your FPV Goggles or the FPV Monitor. Please make
sure keep the Mobula6 level before arming .Be careful and enjoy your flight now !
3
.
ENT [Bind] to binding with the Mobula6 ,the red LED at the bottom of the flight controller will
blinking slowly ,this indicate binding successfully, and then exist binding mode of your Frsky
transmitter, the red LED at the bottom of the flight controller
will getting to be solid again, this
indicate working normal.
Receiver configuration
Please set Receiver mode to be SPI RX Support from the Configuration tab of the Betaflight
Configurator, then select FRSKY_X Provider for FRSKY D16 MODE or Select FRSKY_D Provider
for FRSKY D8 MODE, don't enable Serial RX since the CRAZYBEE Flight controller is integrated
SPI BUS Receiver
2.Turn on the Frsky transmitter (Use X9D+ as an example) and move to the MIXER interface,
Set “SA” or “SB” switch etc. for Ch5 to ARM/DISARM the motor
.
Happymodel Mobula6 1s Brushless whoop Frsky version
VIN
+
5V
GND
BOOT
BIND
M1
M2
M3
M4
BAT
GND
Binding procedure
1
.
Powering the Mobula6 then the red LED at the bottom of the flight controller will blinking
slowly. And then press the bind butoon ,the red led will getting to be solid ,this indicate the
receiver is in bind mode.
Toggle the AUX1 Switch, the Green LED on
the Flight controller will getting to be solid
Toggle the AUX1 Switch, the Green LED on
the Flight controller will getting to be solid
LED
_
STRIP
TX2
RX2
BOOT
+5V
GND
IR1
RX1
BIND
M1
M2
M3
M4
BUZ-
+5V
BAT
+
3V
-
4
.
35V
GND
TX1
Plug the USB and go to the CLI command tab in te betaflight configurator, then type “frsky_bind"
(Betaflight 3.5.7 firmware), the red LED will getting to be solid ,and it means the receiver is in bind
mode. For betaflight 4.0.X the bind code is "bind_rx_spi" and for Betaflight 4.1.X or 4.2.X version
the bind code is "bind_rx"
Package includes
Qty
1
1
4
1
1
1
4
1
1
1
Item Name
Mobula6 1S 65mm whoop Drone Frame
SPI Receiver Option1: Crazybee F4 Lite FC built-in Frsky SPI D8 RX
SPI Receiver Option2: Crazybee F4 Lite FC built-in Flysky SPI RX
SPI receiver option3:CrazybeeX DXS V1.0 FC built-in DSM2/X SPI RX
0802 KV19000 or KV25000 brushless motor
Gemfan 1219-3 Propellers(4cw+4ccw)
Runcam Nano3 1/3 CMOS 800TVL camera
5.8G 25mw 40ch vtx (Flight controller built-in)
1S 300mah 30C LiHV Battery
1S Lipo/LIHV USB Charger
Propeller disassemble tool
Brand Name: Happymodel
Item Name: Mobula6 1S 65mm Brushless whoop drone BNF version
Wheelbase: 65mm
Size: 80mm*80mm*37mm
Weight: 20g
Receiver option:
Internal SPI Frsky version (Compatible with ACCST D8/D16, Recommend D8 mode)
Internal SPI Flysky version(Compatible with AFHDS and AFHDS-2A Flysky transmitter)
Internal SPI DSM2/DSMX version(Compatible with DSM2/DSMX radio transmitter)
Motor speed option:
0802 KV25000(Race Edition)
0802 KV19000(Regular Edition)
Specifications
