Arm/Disarm the Motor
1.
The Default Arm/Disarm switch for Mobula 7 is AUX1(Channel 5),and
you can also customize it with Betaflight Configurator.
3
.
The default channel map for Mobula 7
Frsky version is TAER1234,
please make sure your transmitter is matched, otherwise it will can't
be armed. Toggle the AUX1 Switch ,the Green LED on the flight
controller will getting to be solid, this indicates the motor was
armed . And also you can found “Armed” displayed on your FPV
Goggles or the FPV Monitor. Please make sure keep the Mobula 7
level before arming .Be careful and enjoy your flight now !
Receiver configuration
Please set Receiver mode to be SPI RX Support from the
Configuration tab of the Betaflight Configurator, then select
FRSKY_X Provider for FRSKY D16 MODE or Select FRSKY_D Provider
for FRSKY D8 MODE, don't enable Serial RX since the CRAZYBEE
Flight controller is integrated SPI BUS Receiver
2.
Turn on the Frsky transmitter (Use X9D+ as an example) and move
to the MIXER interface, Set “SA” or “SB” switch etc. for Ch5 to
ARM/DISARM the motor
.
Binding procedure
2.
Turn on your Frsky Taranis transmitter, and move to BIND OPTION
from SETUP MENU, Choose receiver mode to D8 (Default factory
mode), If you want to usde D16 mode, please change SPI Bus
Receiver Provider
to Frsky_X(Not suggest)
Flight controller connection diagram
Happymodel Mobula 7 1-2S Frsky
Micro brushless FPV racer drone
1.Connect the Mobula7 to computer, then running the Betaflight
configurator,move to CLID Command , type "bind_rx" . The 2pcs
Red LED and 2pcs white LED will getting to be solid, this indicate
the Receiver is in binding mode. If you flash Mobula7 firmware to
4.0.x, the bind code is "bind_rx_spi" or you can still press the bind
button after the Mobula7 power up to getting into bind mode
3
.
ENT [Bind] to binding with the Mobula 7 , the LED Combo(2 red LED
and 2 white led) will blinking slowly on the flight controller ,this
indicate binding successfully, and then exist binding mode of your
Frsky transmitter, the LED Combo(2 red led and 2 white LED) will
getting to be solid again, this indicate working normal.
Toggle the AUX1 Switch, the Green LED on
the Flight controller will getting to be solid
Toggle the AUX1 Switch, the Green LED on
the Flight controller will getting to be solid
1.
P
lease use Betaflight configurator 10.4.0 or 10.4.1 version to
setting the
, the pre-install firmware is not compatible
Mobula 7
with new 10.5.1 configurator. If want to use 10.5.1 configurator,
please update Betaflight firmware to V4.0.0 or latest
Bind
code
for
BF
V4
.
0
.
0
/
V4
.
0
.
1
/
V4
.
0
.
2
Bind
code
for
default
factory
firmware
Notes:
Package includes
75mm Brushless Bwhoop75 Frame
Crazybee F4 PRO Frsky receiver
SE0802 KV16000 Motor
40mm propeller(4cw+4ccw)
AIO Camera & VTX
Buzzer
3.8v 250mah 30C/60C battery
USB Lipo/LIHV Charger
1S06 6 way Lipo/LIHV charger
Propeller disassemble tool
Screwdriver
Item Name
Basic version Standard version
1
1
4
1
1
1
4
1
0
1
1
1
1
4
1
1
1
4
0
1
1
1
M3
TX1
IRX1
with
Inverter
for
SBUS
input
M1
M2
GND
+
5V
V
_
OUT
V
_
IN
M4
TX2
RX2
RX1
No
inverter
BOOT
LED Status Meanings
- Solid: Normal work
or
IN
Bind
mode
- Blinking
:
NO
RC
signal
or
Binding
succesfful
LED Status Meanings
- Solid: Normal work
or
IN
Bind
mode
- Blinking
:
NO
RC
signal
or
Binding
succesfful
BIND
GND
+
5V
LED
_
STRIP
BUZZ
+
BUZZ
-
VCC
+
2
-
3S
Lipo
GND
