HappyJapan HCD3E Page 27 Instruction Book Download

Page: 27 / 362

-CU -27

3_A TA01

3-8a

DRIVE MODE

Frame change

Change the frame according to the pattern to embroider.

This helps to confirm positioning between the embroidery area and the pattern.

1. Press

2. Press

3. Select the type or size of the frame.

Tubular round frame

Tubular square frame, One touch frame

Cap and One-point frame

Square clamp frame, Border frame

Sock frame

User-defined frame

13-A

Special frame

Non registered

13-J

Embroidery area Pattern

Frame recommend func.

15-2

If the setting of “Frame recommend func.”

on “OPTION” is set to “YES”, the frame

display becomes gray when the embroidery

area of frame is smaller than the pattern

size.

You can select the frame, but a warning may

be displayed when you start embroidery.

3-8b

Summary of Contents for HCD3E











































































































































































































































































































































































Search results

Summary of Contents for HCD3E

Reviews:

Related manuals for HCD3E

Brands by name

Popular brands

HappyJapan HCD3E, Instruction Book

Search results

Summary of Contents for HCD3E

Reviews:

Related manuals for HCD3E

Brands by name

Popular brands