Made in the USA by Broadsight Systems, Inc. for Hanwha Techwin
Page 1 of 2
INSTALLATION MANUAL – Height Strip Enclosure
Unpacking
Unpack carefully. This is mechanical equipment and should
be handled with care. If an item appears to have been
damaged in shipment, replace it properly in its carton and
notify the shipper. If any items are missing, notify the
vendor. The shipping carton is the safest container in which
the unit may be transported. Save it for possible future use.
Service
If the unit ever needs repair service, the customer should
contact the vendor for a return materials authorization (RMA)
and shipping instructions.
Care and Maintenance
Perform routine maintenance to keep the unit dust free.
Model Designation
SHD-46VH
Height Strip Enclosure, White
Description
This unit is designed to be installed at eye-level at the exit of
an establishment. The Height Strip includes height labels
allowing a store employee to quickly gauge the height of a
perpetrator exiting the establishment while the camera
captures a facial shot. The camera is sold separately.
Hardware Kit
2 x Cable Ties
2 x Cable Tie Mounts
3 x Plastic Wall Anchors
3 x #8 Cross Recessed self-tapping screw
2 x M3 x 16mm Pan Head Phillips Screw
Tools Required
#2 Cross Recessed Screwdriver (Phillips)
7/32” Socket and Driver
Level
Drill with 3/16” Bit (Optional 1/8” Bit)
Optional: Drill with 9/16” Bit
Optional: De-burr Tool
Certification
Installation should be performed by a licensed professional
and conform to the National Electrical Code (NEC) and any
applicable local codes.
Installation
1.
Choose desired location for camera installation. Verify
mounting structure and surface is capable of supporting
the camera and no obstacle or interference is present
from existing installed devices or wiring.
2.
Measure a distance of 5 feet from the finished floor and
mark vertical location.
3.
Mark centerline of horizontal location.
4.
If routing camera cable into wall, measure 10.25” below
location and mark new vertical location. Use level from
upper location to mark centerline of horizontal location
for lower location. Drill a 9/16” hole at this location.
5.
For upper hole, if using plastic anchors, drill a 3/16” hole
at intersection of the vertical and horizontal marks. If the
anchors are not being used, drill a 1/8” hole in mounting
surface.
6.
Install plastic anchor and/or #8 screw. Do not tighten.
7.
Remove cover from Height Marker Camera by removing
screw from top cover, then slide cover up and away.
8.
If routing camera cable through top knockout, pull cable
back through camera base and re-route to top knockout.
Feed cable through top cap; it will hang loosely until final
step. Route cable to network box and plug in.
9.
If routing cable through wall, feed camera cable through
lower mounting hole, routing as needed to network box
installation location. Plug cable into network box.
10.
Place center mounting keyhole in base over installed #8
screw. Level and align camera base and frame.
11.
Mark top and bottom mounting locations.
12.
Hang camera base frame from upper cable hole.
13.
Drill 3/16” (or 1/8” if not using anchors) holes at
mounting locations marks and install anchors (if used).
14.
Replace base over installed #8 screw, tighten screw,
install and tighten top and bottom mounting screws.
15.
Install camera (not included) as shown using the screws
provided.
16.
Place cover over base frame about 3/4” inch above
bottom of frame. With light pressure, push toward base
and down until cover is seated against bottom of frame
and cover is secure. Ensure camera lens is centered in
the viewing slot. If adjustment is needed, loosen 2x hex
nuts using 7/32” socket. Raise or lower camera bracket
as needed and re-tighten nuts.
17.
Place top cover plate in position
and tighten screw with light
pressure. Do not over torque.
18.
Refer to Quick Installation Guide
for instructions on camera setup
and installation of network box.
Remove top screw
to access camera
Loosen nuts to adjust
camera bracket
