background image

English _

51

 

NETWORK CONNECTION AND SETUP

CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC

1. 

Run device manager. 

It will scan for connected cameras and display them as a list.

2. 

Double-click a camera to access. 

The Internet browser starts and connects to the camera.

 

M

 

`

Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser.

CONNECTING TO THE CAMERA FROM A REMOTE PC VIA THE 

INTERNET

On a remote computer that is not in the Broadband Router’s network cluster is not allowed, users can access 

cameras within a Broadband Router’s network by using the camera’s DDNS URL.

1. 

Before you can access a camera in the Broadband Router network, you should have set the port range 

forward for the Broadband Router.

2. 

From the remote PC, launch the Internet browser and type the DDNS URL address of the camera, or the 

IP address of the Broadband Router in the address bar.  

ex) http://ddns.hanwha-security.com/ID

 

M

 

`

To use DDNS, sign up at the DDNS homepage (http://ddns.hanwha-security.com) and register the product at [

My DDNS

]> 

[

Register Product

].

Summary of Contents for PNO-A6081R

























































Reviews: