![background image](http://html.mh-extra.com/html/hanna-instruments/hi981037/hi981037_user-manual_3049794001.webp)
Auto-Off
From measurement mode, press and hold
the ON/OFF button. The LCD will show
"OFF", "CAL" followed by "d08" (default
setting, 8 minutes). Release the ON/OFF
button. A single press on the ON/OFF button
will change the auto-off timer to "d60" (60
minutes). To disable the auto-off feature
press the ON/OFF button again, LCD will
show "d--". Press and hold to exit.
Clear Calibration
To clear the user calibration and restore the
tester to factory default. From calibration
mode, press and hold the ON/OFF button,
the LCD will show "CLr".
“Err” Message
In calibration mode, if the probe is in the
correct buffer solution and the "Err" message
is displayed, the probe should be cleaned.
Soak the probe in cleaning solution for
20 minutes. Rinse with water and hydrate
electrode in storage solution for a minimum
of 30 minutes before calibrating.
Battery Indicator
When the battery level is low, the tag on the
LCD will blink. When the battery is depleted
the "Erb" message is displayed and the tester
is powered off.
Care & Maintenance
Please read the information below, to ensure the highest possible accuracy:
• Fresh buffer should be used for each calibration, once the sachets are opened
the buffer value can change over time.
• For improved accuracy a two-point calibration is recommended.
• If the electrode is slow or sluggish, soak it in cleaning solution for 20
minutes, and then hydrated in storage solution for a minimum of 30 minutes
before recalibrating the probe.
• If measurements are taken successively, rinse the probe thoroughly in
distilled or deionized water to eliminate cross-contamination.
• When not in use add a few drops of storage solution to the protective cap
to keep the glass tip and the junction hydrated. If storage solution it not
available pH 4.01 or pH 7.01 buffer can be used. Never store the probe in
distilled or deionized water.
Note:
Never immerse the tester over the maximum immersion level.
Accessories
pH Buffer Solution
HI70004P
pH 4.01 buffer solution, 20 mL sachet (25 pcs.)
HI70007P
pH 7.01 buffer solution, 20 mL sachet (25 pcs.)
HI77400P
pH 4.01 & pH 7.01 buffer solution, 20 mL sachet (10 pcs.,
5 each)
Electrode Cleaning Solution
HI700601P
General purpose cleaning solution, 20 mL sachet (25 pcs.)
HI700620P
Cleaning and disinfection solution for skin residuals, 20 mL
sachet (25 pcs.)
HI700621P
Electrode cleaning solution for skin grease and sebum, 20 mL
sachet (25 pcs.)
Electrode Storage Solution
HI70300L
Electrode storage solution, 500 mL
HI70300M
Electrode storage solution, 230 mL
HI70300S
Electrode storage solution, 30 mL dropper
HI9072
Electrode storage solution, 13 mL dropper
Battery Replacement
To change the CR2032 lithium-ion battery, turn
the battery cover, located on the back of the tester,
counterclockwise to unlock. Remove cover and
replace the battery with positive (+) side facing out.
Note:
Only use the battery type specified in
the manual. Old batteries should be disposed
in accordance with local regulations.
Warranty
The
HI981037
is warranted for a period of one year against defects in workmanship
and materials when used for its intended purpose and maintained according
to instructions. This warranty is limited to repair or replacement free of charge.
Damage due to accidents, misuse, tampering or lack of prescribed maintenance
is not covered. If service is required, contact your local Hanna Instruments Office.
If under warranty, report the model number, date of purchase, serial number
and the nature of the problem. If the repair is not covered by the warranty, you
will be notified of the charges incurred. If the tester is to be returned to Hanna
Instruments, first obtain a Returned Goods Authorization (RGA) number from the
Technical Service department and then send it with shipping costs prepaid. When
shipping any tester, make sure it is properly packaged for complete protection.
Recommendations for Users
Before using this product, make sure it is entirely suitable for your specific
application and for the environment in which it is used. Any variation introduced by
the user to the supplied equipment may degrade the tester’s performance. For yours
and the tester’s safety do not use or store the tester in hazardous environments.
Certification
All Hanna Instruments conform to the
CE European Directives
.
Disposal of Electrical & Electronic Equipment
. The product
should not be treated as household waste. Instead hand it over to
the appropriate collection point for the recycling of electrical and
electronic equipment which will conserve natural resources.
Disposal of waste batteries.
This product contains batteries, do
not dispose of them with other household waste. Hand them over
to the appropriate collection point for recycling.
Ensuring proper product and battery disposal prevents potential negative
consequences for the environment and human health. For more information,
contact your city, your local household waste disposal service, the place of
purchase or go to
www.hannainst.com
.
Hanna Instruments reserves the right to modify the design, construction, or
appearance of its products without advance notice.
All rights are reserved. Reproduction in whole or in part is prohibited without the written consent
of the copyright owner, Hanna Instruments Inc., Woonsocket, Rhode Island, 02895, USA.
IST981037 10/19
HI981037
SN: XXXXXXXXX
Made in Ro
mania
RoHS
compliant
HI981037
Skin & Scalp pH Tester
INSTRUCTION MANUAL